Introduction
This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your HISION Cordless Robotic Pool Cleaner. Please read this manual thoroughly before first use to ensure proper functionality and longevity of your device.
Safety Instructions
Adhering to these safety guidelines is crucial for preventing injury and damage to the cleaner:
- Read all instructions carefully before operating the cleaner.
- Do not operate the cleaner outside of water. This can damage the motor and seals.
- Ensure the charging port and the cleaner itself are completely dry before connecting to the charger. Water contact with electrical components can cause electric shock.
- Keep children and pets away from the pool area during the cleaner's operation.
- Use only the original charging adapter provided by HISION. Using unauthorized chargers may damage the battery or cleaner.
- Do not attempt to disassemble or repair the cleaner yourself. Contact HISION customer support for any service needs.
- Avoid operating the cleaner if the water temperature is outside the recommended range (typically 50°F to 95°F / 10°C to 35°C).
Package Contents
Please verify that all the following items are included in your package:
- HISION Robotic Pool Cleaner Unit
- Charging Adapter
- Retrieval Hook
- User Manual
Product Overview
The HISION Cordless Robotic Pool Cleaner is an advanced device designed for efficient and thorough cleaning of both in-ground and above-ground pools. It features a powerful 180W brushless motor for superior suction and is capable of wall-climbing and waterline cleaning, covering areas up to 2000 sq.ft.
Setup
Charging the Cleaner
Before the first use, it is essential to fully charge your robotic pool cleaner. This ensures optimal performance and battery longevity.
- Ensure both the cleaner and its charging port are completely dry before connecting the charger.
- Connect the charging adapter to the cleaner's designated charging port.
- Plug the adapter into a standard power outlet.
- The cleaner's indicator light will show the charging status. A full charge typically takes approximately 2.5 hours.
Initial Placement in the Pool
Once charged, gently place the cleaner into the pool. It will slowly sink to the bottom. Ensure it is fully submerged before activating.
Operating Instructions
Starting the Cleaning Cycle
The HISION Robotic Pool Cleaner is designed for ease of use with a simple one-press start function.
- Ensure the cleaner is fully submerged and resting on the pool floor.
- Press the power button located on the top of the cleaner. The indicator light will illuminate, signaling that the cleaner has started its operation.
Cleaning Modes
The cleaner offers versatile cleaning modes to suit your pool's needs:
- Floor Cleaning: This mode focuses solely on cleaning the pool floor, effectively removing debris from the bottom surface.
- Wall Cleaning: In this mode, the cleaner will ascend pool walls and scrub the waterline, addressing dirt and grime that accumulates at the water's edge.
- All-Coverage Cleaning: This comprehensive mode combines both floor and wall cleaning, ensuring a complete and thorough clean of your entire pool.
Smart Navigation
The HISION cleaner is equipped with SonarNav Pro Navigation Technology, allowing it to intelligently map your pool's layout. This ensures efficient cleaning paths, minimizing missed spots and maximizing coverage. When the battery level is low, the cleaner will automatically self-park near a wall for convenient retrieval.
Retrieving the Cleaner
After the cleaning cycle is complete or when the battery is low, the cleaner will automatically move to a wall for easy retrieval. Use the provided retrieval hook to gently pull the cleaner to the surface of the water.
Official Product Video
This video demonstrates the HISION Cordless Robotic Pool Cleaner's key features, including its one-press start, powerful 180W suction, rapid charging, wall and waterline cleaning capabilities, smart navigation, and self-parking function.
Maintenance
Cleaning the Filter Basket
Regular cleaning of the filter basket is essential to maintain the cleaner's suction power and overall efficiency.
- After each cleaning cycle, remove the cleaner from the pool.
- Open the top cover of the cleaner and carefully remove the filter basket.
- Empty any accumulated debris from the basket into a waste receptacle.
- Rinse the filter basket thoroughly with a garden hose until all remaining debris and fine particles are removed.
- Reinsert the clean filter basket into the cleaner and securely close the top cover.
General Cleaning and Storage
To ensure the longevity of your cleaner:
- After each use, rinse the exterior of the cleaner with fresh water to remove any chlorine or chemical residue.
- Store the cleaner in a cool, dry place, away from direct sunlight and extreme temperatures.
- If storing for an extended period, ensure the battery is fully charged before storage and recharge it every three months to maintain battery health.
Troubleshooting
This section addresses common issues you might encounter and provides solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Cleaner does not start | Low battery; Power button not pressed correctly | Fully charge the cleaner; Press the power button firmly until the indicator light illuminates. |
| Poor cleaning performance | Full filter basket; Clogged suction ports; Worn brushes | Clean the filter basket; Check and clear any obstructions from suction ports; Inspect and replace worn brushes if necessary. |
| Cleaner gets stuck or moves erratically | Obstruction in pool (toys, large debris); Uneven pool surface; Air trapped inside cleaner | Remove all large obstructions from the pool; Reposition cleaner in a clear area; Gently shake the cleaner underwater to release trapped air. |
| Cleaner does not climb walls or clean waterline | Low battery; Excessive algae on walls; Incorrect cleaning mode selected; Water chemistry imbalance | Fully charge the cleaner; Brush pool walls to remove algae; Ensure wall-climbing or all-coverage mode is selected; Check and balance pool water chemistry. |
| Cleaner stops mid-cycle | Low battery; Overload protection activated; Cleaner stuck | Retrieve and charge the cleaner; Check for obstructions or tangled debris; Clear any blockages. |
Specifications
Detailed technical specifications for your HISION Robotic Pool Cleaner:
| Feature | Detail |
|---|---|
| Model | SAT30 |
| Brand | HISION |
| Control Method | App |
| Lithium Battery Voltage | 21.6 Volts |
| Lithium Battery Energy Content | 170.82 Watt Hours |
| Runtime | Up to 150 minutes (Floor Mode Only) |
| Charging Time | Approximately 2.5 hours |
| Max Cleaning Area | Up to 2000 Sq.Ft |
| Suction Power | 180W |
| Product Dimensions | 15.1 x 9.8 x 16.8 inches |
| Material | Acrylonitrile Butadiene Styrene (ABS) |
| Installation Type | Robotic |
Warranty and Support
The HISION Cordless Robotic Pool Cleaner comes with a limited warranty. The product description indicates a potential 2+1 Years Coverage, which typically means a standard 2-year warranty with an additional 1-year extended coverage, possibly upon product registration or specific conditions. Please refer to the warranty card included in your package for the most accurate and specific terms and conditions.
For technical support, troubleshooting assistance, or to inquire about warranty claims, please contact HISION customer service. Contact information can usually be found on the official HISION website or through the platform where you purchased the product.
For detailed warranty information and customer support, please visit the official HISION website or contact your retailer.