VGR 285 Professional Hair Clippers User Manual

Introduction

The VGR 285 Hair Clipper is a high-performance, cordless grooming tool designed for precise and efficient hair cutting. This manual provides essential information for the safe and effective use, setup, operation, and maintenance of your VGR 285 Hair Clipper.

Safety Information

Always unplug the clipper before changing or cleaning the blades. Avoid using the clipper near water. Keep the clipper away from heat sources. Do not ingest or inhale small parts. Keep out of reach of children. Always supervise children when using the clipper. Dispose of used blades and trimmings responsibly.

Package Contents

Verify that all items are present in your VGR 285 Hair Clipper package:

• VGR 285 Hair Clipper Unit
• 6 Magnetic Guide Combs (1.5mm, 3mm, 4.5mm, 6mm, 10mm, 13mm)
• 1 Styling Comb
• Blade Oil
• Cleaning Brush
• USB Charging Cable

Product Overview

Key Components

1. Ceramic and Powder Metallurgic Blade: Self-sharpening blades for precise cutting.
2. Adjustable Taper Lever: Allows for fine-tuning cutting lengths from 0.8mm to 2mm.
3. Power Switch: On/Off control.
4. LED Display: Shows remaining battery level.
5. High-Speed Motor: Delivers 9000 RPM for efficient cutting.

Setup

Initial Charging

1. Connect the USB charging cable to the clipper's charging port.
2. Plug the other end of the USB cable into a compatible USB power adapter (not included) or a computer USB port.
3. The LED display will indicate the charging status. A full charge takes approximately 2.5 hours and provides up to 150 minutes of cordless operation.

Attaching Guide Combs

1. Select the desired magnetic guide comb for your preferred hair length.
2. Align the comb with the clipper blade and gently push it until it securely snaps into place.
3. To remove, simply pull the comb away from the blade.

Operating Instructions

Powering On/Off

Press the power switch to turn the clipper on or off. The LED display will illuminate when the clipper is on.

Adjusting Cutting Length (Without Guide Comb)

1. Locate the adjustable taper lever on the side of the clipper.
2. Move the lever up or down to select a cutting length between 0.8mm and 2mm.
3. This adjustment allows for precise fading and blending.

Using Guide Combs

1. Attach the desired guide comb as described in the 'Setup' section.
2. Ensure the comb is firmly attached before use.
3. Begin cutting hair by moving the clipper against the direction of hair growth.
4. Use the included styling comb to guide hair for an even cut.

Maintenance

Cleaning the Blades

1. Ensure the clipper is turned off and unplugged.
2. Use the provided cleaning brush to remove any loose hair from the blades and the clipper head.
3. For a more thorough cleaning, the blades can be carefully detached (refer to specific blade removal instructions if provided in a separate diagram, otherwise proceed with caution).

Oiling the Blades

1. After cleaning, apply a few drops of the included blade oil to the teeth of the blades.
2. Turn the clipper on for a few seconds to distribute the oil evenly.
3. Wipe off any excess oil with a soft cloth. Regular oiling ensures optimal cutting performance and blade longevity.

Troubleshooting

If you encounter any issues with your VGR 285 Hair Clipper, please review the following general advice:

• Clipper not turning on: Ensure the battery is charged. Connect the clipper to the USB charging cable and allow it to charge for at least 30 minutes before attempting to power it on again.
• Poor cutting performance: Clean the blades thoroughly and apply blade oil. Ensure no hair is trapped between the blades. Check if the blades are dull and consider professional sharpening or replacement if necessary.
• Clipper running hot: This can occur during extended use. Allow the clipper to cool down before continuing. Ensure blades are clean and oiled to reduce friction.

For further assistance, please contact VGR customer support.

Specifications

Warranty and Support

VGR products typically come with a 1-year warranty. For any product inquiries, technical support, or warranty claims, please contact VGR customer service. Support is generally available within 24 hours.