OLIXIS Criss Cross Chair (Model AOL-J37261TPK) Instruction Manual

Introduction

Thank you for choosing the OLIXIS Criss Cross Chair. This manual provides essential information for the safe and efficient use of your new chair. Please read it thoroughly before assembly and retain it for future reference.

This chair is designed for comfort and versatility, featuring a wider seat to accommodate various sitting postures, including cross-legged. Its ergonomic design and adjustable features make it suitable for home offices, study rooms, and other personal workspaces.

Product Features

• Wider Seat Width: The 26-inch seat width and 18.7-inch seat depth provide ample room, allowing for comfortable cross-legged sitting.
• Comfortable Padded Seat: The seat cushion and backrest are filled with high-density sponge, conforming to an ergonomic structure for extended sitting comfort. The upgraded teddy fleece material is designed for durability and reduced shedding.
• Height Adjustable: The chair's height is adjustable, with a range from 15.94 inches to 19.69 inches (from seat cushion to floor), making it adaptable for various table heights and users including teenagers, adults, and seniors.
• 360° Swivel: The armless design allows the seat to rotate 360 degrees, enhancing convenience and saving space in your home office.
• Sturdy Construction: Equipped with an SGS-certified gas spring and a cross-structured metal base, the chair supports up to 300 lbs. The chair feet feature a non-slip, scratch-resistant rubber bottom.
• Locking Rocking Function: A knob under the seat cushion allows you to engage a 21° rocking function, suitable for relaxation during reading, watching TV, or gaming.

Setup and Assembly

Your OLIXIS Criss Cross Chair comes with all necessary assembly tools and a user manual. Follow the steps below for proper setup.

Assembly Steps:

1. Insert the Gas Lift (D) into the Leg (E).
2. Attach the Mechanism (C) to the Seat Cushion (B) using Wrench (H) and Bolts (F)*4. Ensure the "FRONT" direction of the Mechanism (C) and Seat Cushion (B) are aligned.
3. Align the screw holes on the Seat Cushion (B) and Backrest (A). Using Wrench (H), secure both completely with Bolts (G)*4.
4. Align the hole on Mechanism (C) with Gas Lift (D), and press the Chair down until it is fully secured.

Image: An exploded view showing all components of the OLIXIS Criss Cross Chair, including the backrest, seat cushion, mechanism, gas lift, leg base, bolts, and wrench, laid out for assembly.

Operating Instructions

Height Adjustment:

To adjust the chair's height, locate the lever on the right side beneath the seat. Pull the lever upwards while seated to lower the chair, or stand up and pull the lever upwards to raise the chair. Release the lever at your desired height.

Rocking Function:

To activate the rocking function, turn the knob located under the seat cushion counter-clockwise to loosen it, then pull out the lever on the left side. The chair will now allow a 21° backward tilt. To lock the chair in an upright position, push the lever inwards and tighten the knob by turning it clockwise.

360° Swivel:

The chair seat is designed to swivel freely 360 degrees for easy movement and access around your workspace.

Image: A diagram illustrating the height adjustment lever (up/down) and the rocking function knob (free lock/lock) located beneath the chair's seat, along with a visual of the gas spring and rubber bottom for stability.

Maintenance

Cleaning:

• For general cleaning, use a soft, damp cloth with mild soap and water.
• Avoid harsh chemicals or abrasive cleaners, as these may damage the fabric or finish.
• For the teddy fleece material, gentle vacuuming can help maintain its texture and remove dust.

Care:

• Regularly check all bolts and screws to ensure they are tight. Re-tighten if necessary.
• Avoid exposing the chair to direct sunlight for prolonged periods to prevent fading of the fabric.
• Do not exceed the maximum weight capacity of 300 lbs.

Troubleshooting

• Chair not adjusting height: Ensure the gas lift lever is fully engaged and the gas lift cylinder is properly inserted into the base and mechanism. If the issue persists, the gas lift may need replacement.
• Chair feels unstable: Check all assembly bolts and screws to ensure they are securely tightened. Verify that the leg base is correctly assembled and placed on a flat, even surface.
• Rocking function not working: Make sure the rocking function knob under the seat is loosened and the lever is pulled out. If it's too stiff, try loosening the tension knob further.

Specifications

Image: A front view of the OLIXIS Criss Cross Chair, highlighting its wide seat and armless design in furry pink fabric.

Image: A side view of the OLIXIS Criss Cross Chair, illustrating its ergonomic profile and the potential for a slight backward rock.

Image: A back view of the OLIXIS Criss Cross Chair, showcasing the robust cross-structured metal base and the chair's overall stability.

Image: A close-up view demonstrating the high-density sponge padding used in the OLIXIS chair's seat cushion, indicating comfort and support.

Warranty and Support

For any questions, concerns, or support needs regarding your OLIXIS Criss Cross Chair, please refer to the contact information provided with your purchase documentation or visit the official OLIXIS website. Keep your proof of purchase for warranty claims.

OLIXIS is committed to customer satisfaction and provides support for product-related inquiries.