ELEGOO Saturn 4 Ultra 16K
Contents
ELEGOO Saturn 4 Ultra 16K 3D Printer User Manual
Model: Saturn 4 Ultra 16K
1. Introduction
Thank you for choosing the ELEGOO Saturn 4 Ultra 16K 3D Printer. This manual provides essential information for setting up, operating, and maintaining your new 3D printer. Please read it thoroughly before use to ensure optimal performance and safety.

Figure 1: ELEGOO Saturn 4 Ultra 16K 3D Printer and a sample print.
2. Safety Information
Always observe the following safety precautions:
- Ensure proper ventilation when operating the printer, especially when handling resin.
- Wear appropriate personal protective equipment (PPE), such as gloves and safety glasses, when handling liquid resin or cleaning the printer.
- Keep the printer away from direct sunlight, heat sources, and flammable materials.
- Do not touch the build plate or resin tank during operation.
- Dispose of waste resin and cleaning materials according to local regulations.
- Keep out of reach of children and pets.
3. Setup and Initial Preparation
3.1 Unpacking and Inspection
Carefully remove all components from the packaging. Inspect for any damage during transit. Refer to the packing list to ensure all parts are present.
3.2 Printer Placement
Place the printer on a stable, level surface in a well-ventilated area, away from direct sunlight.
3.3 Build Plate Installation and Leveling
The ELEGOO Saturn 4 Ultra 16K features intelligent mechanical sensors for automatic leveling. Simply unpack and power on the printer for calibration. If auto-leveling fails, manual leveling can be performed via the settings menu.

Figure 2: Automatic leveling with intelligent sensors.
3.4 Resin Tank Preparation
Install the resin tank onto the printer. Ensure it is securely seated. The printer features dual drain ports for easy resin management.

Figure 3: Convenient design features including quick-release and dual fill ports.
4. Operating Instructions
4.1 Power On and User Interface
Connect the power adapter and turn on the printer. The 4.0-inch capacitive touchscreen provides an intuitive interface. The system supports 12 languages.
4.2 Resin Filling and Heating
Pour resin into the tank, ensuring it does not exceed the MAX fill line. The printer features intelligent resin tank heating with automatic temperature measurement and heating functions. It can preheat resin for 24 hours, maintaining an optimal printing temperature of 30°C.

Figure 4: Intelligent resin tank heating maintains optimal temperature.
4.3 Preparing Print Files
Use compatible slicing software (e.g., Chitubox) to prepare your 3D models. The printer supports ultra-fast printing up to 150 mm/h using tilt-release technology, which separates the cured model from the release film efficiently. You can switch between fast and slow print modes for quality or speed.

Figure 5: Tilt-Release Technology for ultra-fast printing.
4.4 Transferring Print Files (Wi-Fi Cluster Printing)
Transfer files via Wi-Fi (2.4 GHz and 5 GHz networks supported) at speeds of 6-10 Mbps, eliminating the need for a USB stick. The Wi-Fi cluster printing feature allows simultaneous printing on multiple printers within a local network, with remote control and monitoring capabilities.

Figure 6: Wi-Fi Cluster Printing for efficient multi-printer operation.
4.5 Monitoring Prints (AI Camera)
The built-in AI camera allows real-time monitoring and time-lapse photography of your prints. It can intelligently detect issues such as empty build plates or warped models, enabling timely intervention. An integrated high-brightness light illuminates the printing process for 24/7 monitoring.

Figure 7: AI Camera for intelligent print monitoring.
4.6 Post-Printing
After printing, remove the build plate and carefully detach the printed model. Clean the model using appropriate methods (e.g., isopropyl alcohol) and cure it under UV light to achieve final hardness.
5. Maintenance
5.1 Cleaning the Resin Tank and Build Plate
Regularly clean the resin tank and build plate with isopropyl alcohol. Ensure no cured resin particles remain in the tank, as they can damage the LCD screen.
5.2 LCD Screen Protection
The 16K monochrome LCD screen is protected by a 9H hardness tempered film, offering excellent scratch and damage resistance. Keep the screen clean and free of dust and resin spills.

Figure 8: High-resolution 16K LCD screen with protective film.
5.3 Firmware Updates
The advanced system supports OTA (Over-The-Air) firmware updates, making system updates easier. Check for available updates periodically to ensure optimal performance and access to new features.
6. Troubleshooting
This section addresses common issues you might encounter with your ELEGOO Saturn 4 Ultra 16K 3D Printer.
| Problem | Possible Cause | Solution |
|---|---|---|
| Print failure / Model not adhering to build plate | Improper leveling, insufficient exposure time, cold resin, dirty build plate. | Re-level the build plate. Increase bottom exposure time. Ensure resin is at optimal temperature (30°C). Clean the build plate thoroughly. |
| Printer stops mid-print | Resin shortage, foreign objects in tank, power outage, LED temperature too high. | The printer can intelligently detect resin shortage, foreign objects, or high LED temperature and warn you. If a power outage occurs, printing can resume after power is restored. Address the specific warning. |
| Poor print quality / Details missing | Incorrect exposure settings, old resin, dirty LCD screen, worn FEP film. | Adjust exposure settings in slicing software. Use fresh resin. Clean the LCD screen. Inspect and replace FEP film if necessary. |
| Wi-Fi connection issues | Incorrect network settings, signal interference. | Ensure correct Wi-Fi password. Check network compatibility (2.4GHz/5GHz). Move printer closer to router or reduce interference. |

Figure 9: Intelligent sensors detect issues like resin shortage or foreign objects.
7. Specifications
| Feature | Detail |
|---|---|
| Model | ELEGOO Saturn 4 Ultra 16K |
| Printing Technology | MSLA (Masked Stereolithography) with Tilt-Release |
| Build Volume (LWH) | 211.68 x 118.37 x 220 mm³ |
| LCD Screen | 16K Monochrome LCD |
| Resolution | 15120 x 6230 px |
| XY Resolution | 14 x 19 µm |
| Max Printing Speed | Up to 150 mm/h |
| Leveling | Automatic Leveling with Intelligent Mechanical Sensors |
| Connectivity | Wi-Fi (2.4GHz & 5GHz), USB |
| Additional Features | AI Camera, Intelligent Resin Tank Heating, Power Outage Resume, OTA Updates, 4.0-inch Capacitive Touchscreen |
| Material | Metal |
| Item Weight | 16.1 Kilograms |
| Product Dimensions | 40.3D x 43.6W x 62.3H cm |

Figure 10: Large build volume of 211.68 x 118.37 x 220 mm³.
8. Warranty and Support
ELEGOO provides a standard warranty for its products. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official ELEGOO website. For technical support, troubleshooting assistance, or spare parts, please contact ELEGOO customer service through their official channels.
Manufacturer: ELEGOO
ASIN: B0DT97Y26L
Manufacturer Reference: YES-DE-3D-S4U16
First Available: January 17, 2025
Documents and downloads
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.