Introduction
This manual provides essential information for the proper installation, maintenance, and care of your roborock Washable Filter Replacement. Adhering to these instructions will help ensure optimal performance and longevity of your filter and compatible roborock vacuum cleaner.
Compatibility
The roborock Washable Filter Replacement is designed for use with the following roborock cordless wet dry vacuum cleaner models:
- Roborock F25
- Roborock F25 GT
- Roborock F25 LT
- Roborock F25 RT
- Roborock F25 ACE
- Roborock F25 ALT
- Roborock F25 ACE Combo
- Roborock F25 Combo
What's Included
Each package of the roborock Washable Filter Replacement contains:
- 2 x Roborock Washable Filters
Setup and Installation
Replacing the filter in your roborock F25 series vacuum cleaner is a straightforward process that requires no special tools.
- Ensure the vacuum cleaner is turned off and unplugged from its power source.
- Locate the filter compartment on your roborock F25 series vacuum cleaner. Refer to your vacuum cleaner's main instruction manual for the exact location if needed.
- Open the filter compartment.
- Carefully remove the old filter.
- Insert the new roborock Washable Filter Replacement into the compartment, ensuring it snaps securely into place.
- Close the filter compartment.
The filter is designed for quick and effortless replacement, ensuring your vacuum cleaner maintains optimal performance.
Operating Considerations
Once the new filter is installed, your roborock F25 series vacuum cleaner is ready for operation. The filter plays a crucial role in capturing dust and debris, contributing to the appliance's overall cleaning efficiency and maintaining air quality during use. Regular maintenance, as described in the next section, is key to ensuring the filter performs effectively over time.
Maintenance
To ensure your roborock Washable Filter Replacement delivers long-lasting, effective air filtration and to keep your machine running at peak performance, regular cleaning is essential.
- Removal: Turn off and unplug the vacuum cleaner. Remove the filter as described in the "Setup and Installation" section.
- Washing: Rinse the filter under running water until all visible dirt and debris are removed. You may gently tap the filter to dislodge stubborn particles. Avoid using harsh detergents or brushes that could damage the filter material.
- Drying: This is a critical step. After washing, allow the filter to air dry completely for at least 24 hours before re-installing it into the vacuum cleaner. Do not use a dryer or any heat source to speed up the drying process, as this can damage the filter. Ensure the filter is thoroughly dry to prevent mold growth and maintain filtration efficiency.
- Frequency: Weekly cleaning is recommended, but the frequency may vary based on your usage and the level of debris collected.
Proper maintenance extends the life of the filter and ensures your vacuum cleaner continues to provide high-performance cleaning.
Troubleshooting
If you experience issues with your roborock F25 series vacuum cleaner after filter replacement or during use, consider the following:
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced suction power | Clogged or dirty filter; improperly installed filter. | Clean the filter thoroughly and ensure it is completely dry before re-installing. Verify the filter is correctly seated in its compartment. If the filter is old or damaged, replace it with a new one. |
| Unusual odors from vacuum | Filter not dried completely after washing; trapped debris causing odor. | Remove and wash the filter, ensuring it is completely dry before re-installation. Check for any other debris or residue within the vacuum cleaner that might be causing the odor. |
| Filter does not fit | Incorrect filter model; improper alignment during installation. | Verify that you have the correct roborock Washable Filter Replacement (Model: SCLWTZ09RR) for your specific roborock F25 series vacuum cleaner model. Ensure the filter is aligned correctly before attempting to snap it into place. Do not force the filter. |
Specifications
| Feature | Detail |
|---|---|
| Brand | roborock |
| Model Number | SCLWTZ09RR |
| Item Weight | 3.2 ounces |
| Product Dimensions | 3.14 x 1.18 x 3.89 inches |
| Material Type | Acrylonitrile Butadiene Styrene (ABS) |
| Reusability | Reusable |
| Included Components | 2 filters |
Warranty and Support
Warranty information for replacement parts like this filter is typically covered under the warranty of the main roborock F25 series vacuum cleaner or may be subject to specific terms for accessories. Please refer to the warranty documentation provided with your original roborock vacuum cleaner or visit the official roborock website for detailed warranty policies.
For further assistance, technical support, or to purchase additional accessories, please visit the official roborock store or contact roborock customer service:
- Official Roborock Store: Visit Roborock Store on Amazon
- For general inquiries, please refer to the support section on the official roborock website.
