Amesias Drain Pump Motor Instruction Manual

Introduction

This manual provides essential information for the installation, operation, maintenance, and troubleshooting of your Amesias Drain Pump Motor. This component is designed as a replacement part for specific Kenmore washing machine models. Please read these instructions carefully before attempting any installation or repair to ensure safe and correct usage.

Safety Warning:

• Always disconnect power to the washing machine before beginning any repair or maintenance.
• Turn off the water supply to the washing machine.
• Wear appropriate personal protective equipment, such as gloves and eye protection.
• If you are unsure about any step, consult a qualified appliance repair technician.

Compatibility

This Amesias Drain Pump Motor is compatible with the following Kenmore washing machine models:

• 79641073310, 79641073311
• 79641162410, 79641162411
• 79641172210, 79641172211
• 79641182310, 79641182311
• 79641272210, 79641272211
• 79641282310, 79641282311
• 79641283310, 79641283311

Important: Verify your washing machine's model number before installation.

Image: A red stop sign graphic emphasizing the importance of checking your appliance's model number for compatibility before purchasing or installing a replacement part. Many parts may appear similar but are not interchangeable.

Setup and Installation

Replacing a drain pump motor requires basic mechanical skills. Follow these general steps. Specific procedures may vary slightly by washer model. Refer to your washing machine's service manual for detailed instructions.

Image: The Amesias Drain Pump Motor, featuring a black motor housing and a white impeller visible at the outlet. This image shows the overall design of the replacement part.

1. Preparation: Disconnect the washing machine from the electrical outlet and turn off the water supply. Move the washer away from the wall to access the rear or bottom panel.
2. Access the Pump: Depending on your washer model, you may need to remove the front panel, rear panel, or tilt the washer back to access the drain pump. Consult your washer's service manual for exact access points.
3. Drain Residual Water: Place a shallow pan or towels under the pump area to catch any residual water in the hoses.
4. Disconnect Hoses: Carefully remove the clamps and disconnect the inlet and outlet hoses from the old drain pump. Be prepared for water spillage.
5. Disconnect Wiring: Unplug the electrical connector(s) from the old drain pump motor.
6. Remove Old Pump: Unmount the old drain pump from its housing or base. This usually involves releasing clips or unscrewing fasteners.
7. Install New Pump: Position the new Amesias Drain Pump Motor in place and secure it with the clips or screws removed earlier.
8. Reconnect Wiring and Hoses: Attach the electrical connector(s) to the new pump. Reconnect the inlet and outlet hoses, securing them with their clamps. Ensure all connections are tight to prevent leaks.
9. Test: Restore power and water supply to the washing machine. Run a short drain/spin cycle to check for proper operation and any leaks before pushing the washer back into place.

Operating Instructions

The Amesias Drain Pump Motor operates automatically as an integral part of your washing machine's wash and spin cycles. It is designed to efficiently remove water from the wash tub at the appropriate times during the cycle. No direct user operation is required for the pump itself.

Ensure your washing machine is loaded correctly and cycles are selected according to your appliance's user manual. The drain pump will activate as needed to facilitate proper water drainage.

Maintenance

The drain pump motor is a sealed unit and does not require specific user maintenance. However, to ensure the longevity and efficient operation of your washing machine's drainage system, consider the following general maintenance tips:

• Clean the Lint Filter/Coin Trap: Many washing machines have a filter or coin trap accessible from the front or bottom. Regularly clean this filter to prevent lint, coins, or small objects from reaching and potentially damaging the drain pump.
• Avoid Overloading: Overloading the washer can strain components, including the drain pump.
• Use Appropriate Detergent: Use only high-efficiency (HE) detergent in HE washers to prevent excessive suds that can hinder drainage.
• Inspect Hoses: Periodically check drain hoses for kinks, blockages, or damage that could impede water flow.

Troubleshooting

If your washing machine is experiencing drainage issues after installing the new pump, consider these common troubleshooting steps:

• Washer Not Draining:
  • Ensure the washing machine is plugged in and receiving power.
  • Check for kinks or blockages in the drain hose.
  • Verify that the lint filter/coin trap (if applicable) is clean and free of debris.
  • Confirm all electrical connections to the pump are secure.
• Unusual Noises During Drain Cycle:
  • Small objects (coins, buttons) may be trapped in the pump impeller. Disconnect power and water, then carefully inspect the pump's inlet and impeller area.
  • Ensure the pump is securely mounted and not vibrating against other components.
• Leaking:
  • Check all hose connections to the pump for tightness. Ensure clamps are properly seated.
  • Inspect hoses for cracks or damage.

If these steps do not resolve the issue, it is recommended to contact a qualified appliance repair technician.

Specifications

Warranty Information

This Amesias Drain Pump Motor comes with a LIFETIME WARRANTY from the manufacturer. For details regarding warranty claims, terms, and conditions, please retain your proof of purchase and contact the seller or manufacturer directly.

Support

For technical assistance, warranty inquiries, or further questions regarding your Amesias Drain Pump Motor, please contact the seller through your purchase platform or refer to the manufacturer's official website for support contact information.