Tissot Seastar 1000 Quartz GMT Watch Instruction Manual

Introduction

This manual provides essential instructions for the proper use, care, and maintenance of your Tissot Seastar 1000 Quartz GMT watch. Designed for reliability and precision, this timepiece combines robust water resistance with a Swiss Made quartz movement and GMT functionality. Please read this manual thoroughly to ensure optimal performance and longevity of your watch.

Figure 1: Front view of the Tissot Seastar 1000 Quartz GMT watch, showcasing the dial, bezel, and hands.

Setup

Unboxing and Initial Inspection

Upon receiving your Tissot Seastar 1000 Quartz GMT watch, carefully remove it from its packaging. Inspect the watch for any visible damage or irregularities. Ensure all protective films are removed from the crystal, case back, and bracelet/strap.

Strap Adjustment

The watch features an interchangeable quick-release rubber strap. To adjust the fit, locate the buckle and adjust the pin to the desired hole on the strap. For significant adjustments or strap replacement, professional assistance is recommended to avoid damage.

Figure 2: The Tissot Seastar 1000 Quartz GMT watch worn on a wrist, demonstrating its fit.

Operating Instructions

Your Tissot Seastar 1000 Quartz GMT watch is equipped with a screw-down crown for enhanced water resistance. Always ensure the crown is fully screwed down after any adjustments.

Figure 3: Side view of the watch, highlighting the screw-down crown.

Figure 4: Close-up of the watch dial, showing the main hands, GMT hand, date window, and luminous markers.

Crown Positions

1. Position 0 (Screwed Down): Normal operating position, ensures water resistance.
2. Position 1 (Unscrewed, Pushed In): For quick date adjustment.
3. Position 2 (Pulled Out One Click): For setting the GMT hand.
4. Position 3 (Pulled Out Two Clicks): For setting the time and stopping the seconds hand.

Figure 5: A hand demonstrating the adjustment of the watch crown.

Setting the Time

1. Unscrew the crown counter-clockwise until it springs out.
2. Pull the crown out to Position 3 (two clicks). The seconds hand will stop.
3. Rotate the crown to move the hour and minute hands to the correct time. Ensure the 24-hour GMT hand is also correctly aligned with the main time if it's not being used for a second time zone.
4. Once set, push the crown back to Position 0 and screw it down clockwise firmly to ensure water resistance.

Setting the Date

1. Unscrew the crown counter-clockwise until it springs out.
2. Pull the crown out to Position 1 (one click).
3. Rotate the crown clockwise or counter-clockwise to adjust the date. Avoid setting the date between 9 PM and 3 AM, as this can damage the movement.
4. Once set, push the crown back to Position 0 and screw it down clockwise firmly.

Setting the GMT (Second Time Zone)

The red GMT hand indicates a second time zone on a 24-hour scale, read against the rotating bezel.

1. Unscrew the crown counter-clockwise until it springs out.
2. Pull the crown out to Position 2 (one click, after Position 1).
3. Rotate the crown to move the red GMT hand to the desired 24-hour time.
4. Once set, push the crown back to Position 0 and screw it down clockwise firmly.

The unidirectional rotating bezel can be used to track a third time zone or for dive timing. Rotate the bezel counter-clockwise to align the desired marker with the GMT hand or minute hand for elapsed time measurement.

Maintenance

Water Resistance

Your Tissot Seastar 1000 Quartz GMT watch is water-resistant up to 30 bar (300 meters / 1000 feet). This makes it suitable for short periods of recreational swimming and showering. It is not suitable for diving or snorkeling. Always ensure the crown is fully screwed down before exposing the watch to water. Avoid operating the crown or pushers while the watch is wet or submerged.

After exposure to saltwater, rinse the watch with fresh water and dry it thoroughly with a soft cloth.

Cleaning

Clean your watch regularly with a soft, dry cloth. For more thorough cleaning, especially after contact with sweat or dirt, use a soft brush and soapy water, then rinse with fresh water and dry completely. Ensure the crown is screwed down before using water.

Battery Replacement

The watch is powered by a quartz movement requiring batteries (2 P76 batteries included). When the battery is depleted, the watch may stop or exhibit an End-of-Life (EOL) indicator (if applicable, the seconds hand may jump every few seconds). Battery replacement should only be performed by an authorized Tissot service center or a qualified watchmaker to maintain water resistance and warranty validity.

General Care

• Avoid exposing your watch to extreme temperatures (above 60°C / 140°F or below 0°C / 32°F) or sudden temperature changes.
• Protect your watch from strong impacts and vibrations.
• Keep the watch away from strong magnetic fields, which can affect the accuracy of quartz movements.
• Avoid contact with solvents, detergents, perfumes, and cosmetic products, as they can damage the case, strap, or gaskets.

Troubleshooting

Watch Not Running

• Check Crown Position: Ensure the crown is fully pushed in and screwed down (Position 0). If it's pulled out, the watch will not run.
• Battery Depletion: If the watch has stopped completely, the battery may need replacement. Refer to the "Battery Replacement" section under Maintenance.

Incorrect Time or Date

• Reset Time/Date: Follow the instructions in the "Operating Instructions" section to correctly set the time, date, and GMT hand.
• Magnetic Interference: Strong magnetic fields can temporarily affect quartz watch accuracy. If suspected, keep the watch away from magnetic sources.

If problems persist, contact an authorized Tissot service center for assistance.

Specifications

Figure 6: Case back of the watch, displaying water resistance rating, material, and model information.

Warranty

Your Tissot Seastar 1000 Quartz GMT watch comes with a 2-Year International Warranty from the date of purchase. This warranty covers material and manufacturing defects. It does not cover normal wear and tear, damage caused by improper handling, lack of care, accidents, or unauthorized repairs.

To claim warranty service, please present your dated warranty card or proof of purchase to an authorized Tissot retailer or service center. Any intervention by a non-authorized third party will void the warranty.

Support

For further assistance, service, or genuine spare parts, please contact an authorized Tissot retailer or visit the official Tissot website. You can find more information and locate service centers via the Tissot Store on Amazon or the manufacturer's official channels.

Manufacturer: Tissot SA