Transformers Hot Wheels Collaborative Twin Mill Deluxe Class Action Figure Instruction Manual

Introduction

This manual provides detailed instructions for the assembly, transformation, and care of your Transformers Collaborative Hot Wheels x Twin Mill Deluxe Class Action Figure. This 5-inch (12.5 cm) figure converts between robot action figure and Twin Mill-inspired car mode, offering dynamic play and display options. Please read all instructions carefully before use.

Safety Information

WARNING: CHOKING HAZARD – Small parts may be generated. Not for children under 3 years.

Recommended age: 8 years and up.

What's in the Box

• One (1) Twin Mill Action Figure
• Two (2) Flame Accessory Pieces

Setup and Initial Inspection

Upon opening the package, carefully remove all components. Inspect the figure and accessories for any damage or missing parts. Ensure all joints move freely but are firm enough to hold poses. The figure comes with two flame accessory pieces that can be attached in either robot or car mode.

Operating Instructions: Transformation

Transforming to Robot Mode (21 Steps)

Follow these steps to convert your Twin Mill figure from car mode to robot mode:

1. Remove the two flame accessory pieces if attached.
2. Carefully detach the engine/exhaust sections from the car mode. These will become the robot's weapons.
3. Lift the canopy section of the car.
4. Rotate the canopy section to reveal the robot head.
5. Separate the rear section of the car to begin forming the legs.
6. Unpeg the leg sections and extend them downwards.
7. Rotate the feet into position and extend the heel spurs for stability.
8. Close the leg panels, ensuring they tab into place.
9. Rotate the waist.
10. Bring the front car sections (which form the robot's chest and shoulders) forward.
11. The robot head will automatically pop up.
12. Rotate the shoulder sections so the car wheels face upwards.
13. Extend the arms downwards from the shoulder area.
14. Rotate the forearms to reveal the fists.
15. Ensure all panels are securely tabbed and aligned for a stable robot mode.

Image: Twin Mill figure in its robot mode, standing upright with a dynamic pose. The figure is predominantly blue with lighter blue accents, showcasing its detailed design.

Image: Twin Mill figure in robot mode, holding the flame accessory pieces attached to its arms, simulating firing effects. The figure is blue with light blue details.

Transforming to Vehicle Mode (21 Steps)

To convert your Twin Mill figure from robot mode back to car mode, reverse the steps above:

1. Remove any attached flame accessories.
2. Retract the fists and fold the forearms into the arm sections.
3. Fold the arms upwards and inward, aligning them with the shoulder sections.
4. Collapse the robot head into the chest cavity.
5. Fold the chest section (front of the car) back into place.
6. Rotate the shoulder sections so the car wheels are positioned correctly for vehicle mode.
7. Unfold the leg panels.
8. Retract the heel spurs and fold the feet into the leg sections.
9. Collapse the leg sections upwards and together to form the rear of the car.
10. Align and tab the two halves of the car body together.
11. Reattach the engine/exhaust sections to the top of the car.
12. Ensure all panels are flush and securely tabbed to form a complete and streamlined car mode.

Image: Twin Mill figure in its sleek car mode, showcasing the iconic Hot Wheels design with twin engines and a metallic blue finish with light blue racing stripes.

Image: Twin Mill figure in car mode with the flame accessory pieces attached to the exhaust pipes, simulating speed and power effects.

Attaching Flame Accessories

The two flame accessory pieces can be attached to the figure in both robot and vehicle modes:

• Robot Mode: Insert the peg of each flame accessory into the designated ports on the robot's arms, typically near the hands or weapon attachment points.
• Vehicle Mode: Insert the peg of each flame accessory into the exhaust pipes on either side of the car, ensuring the flame curves backward to simulate motion.

Maintenance

To ensure the longevity of your figure:

• Clean with a soft, dry cloth. Avoid abrasive cleaners or solvents.
• Store in a cool, dry place away from direct sunlight to prevent discoloration or material degradation.
• Avoid excessive force during transformation to prevent breakage of small parts.

Troubleshooting

If you encounter any issues during transformation or play:

• Stiff Joints: Gently work the joint back and forth. Do not force it.
• Parts Not Aligning: Review the transformation steps carefully. Ensure all previous steps are completed correctly and all tabs and slots are properly aligned.
• Loose Parts: If a part becomes loose, check for any visible damage. If the issue persists, contact customer support.

Specifications

Warranty and Support

For warranty information or customer support, please visit the official Transformers brand store or contact Hasbro customer service. Keep your proof of purchase for any warranty claims.

Official Brand Store: Transformers Store on Amazon