Introduction
Thank you for choosing the Bevinsee Carbon Fiber Charge Intercooler Cover. This manual provides essential information for the proper installation, care, and maintenance of your new intercooler cover. Designed for specific S55 engine models, this cover enhances the aesthetic appeal of your engine bay with its premium carbon fiber construction.
Product Overview
The Bevinsee Carbon Fiber Charge Intercooler Cover is crafted from genuine carbon fiber, offering both durability and a sophisticated appearance. It is designed to complement the existing carbon fiber components in your engine bay.
Key Features
- Genuine Carbon Fiber Material: Constructed from authentic carbon fiber for superior strength and a premium feel.
- Matte Black Finish: Features a durable matte black finish that resists yellowing over time, unlike glossy alternatives.
- Easy Installation: Equipped with pre-applied double-sided tape for a straightforward and secure attachment.
- Perfect Fit: Engineered to precisely fit the original engine trim, echoing the factory carbon fiber strut mounts and engine cover.
- Enhanced Aesthetics: Adds a sleek, modern, and high-performance look to the engine bay.
Compatibility
This Charge Intercooler Cover is specifically designed for S55 engine vehicles. Please verify your vehicle's model and engine type before installation.
- M2 Series F87 S55: (2015-2020, Base and Competition Models)
- M3 Series F80 S55: (2013-2020, Base and Competition Models)
- M4 Series F82/F83 S55: (2013-2020, Base and Competition Models)
Installation Guide
Installation of the Bevinsee Carbon Fiber Charge Intercooler Cover is designed to be straightforward. Follow these steps carefully for optimal adhesion and fitment.
Preparation
- Ensure the engine is cool to the touch.
- Thoroughly clean the surface of the intercooler where the cover will be applied. Use an automotive-grade degreaser or isopropyl alcohol to remove any dirt, oil, or wax residues. Allow the surface to dry completely.
- Test fit the carbon fiber cover pieces to ensure proper alignment before removing the tape backing.
Installation Steps
- Carefully peel off the red backing from the double-sided tape on the back of the carbon fiber cover pieces.
- Align each cover piece precisely with its corresponding section on the intercooler.
- Once aligned, firmly press down on the cover for at least 30 seconds to ensure strong adhesion of the tape to the intercooler surface. Apply even pressure across the entire surface of the cover.
- Avoid washing the vehicle or exposing the installed cover to excessive moisture for at least 24-48 hours to allow the adhesive to fully cure.
Care and Maintenance
To maintain the pristine appearance and longevity of your carbon fiber intercooler cover, follow these simple care guidelines:
- Cleaning: Use a soft, damp cloth with mild soap and water to clean the surface. Avoid abrasive cleaners, harsh chemicals, or stiff brushes that could scratch the matte finish.
- Protection: While the matte finish is durable, consider using a carbon fiber specific sealant or wax to provide an extra layer of protection against UV rays and environmental contaminants.
- Inspection: Periodically check the adhesion of the cover, especially after extreme temperature changes or prolonged exposure to vibrations.
Troubleshooting
While issues are rare, here are some common concerns and their solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Cover not adhering properly | Surface not clean; insufficient pressure during installation; low ambient temperature during installation. | Ensure surface is thoroughly cleaned and dry. Apply firm, even pressure for an extended period. Install in a warm environment (above 60°F / 15°C) or gently warm the surface with a heat gun (low setting) before application. |
| Matte finish appears dull or stained | Exposure to harsh chemicals; accumulation of dirt/grime; improper cleaning agents. | Clean with a soft cloth and mild soap/water. Avoid petroleum-based cleaners. For stubborn stains, consult a professional detailer specializing in carbon fiber. |
Specifications
| Attribute | Detail |
|---|---|
| Brand | Bevinsee |
| Model Number | Bevinsee9132009400[US] |
| Material | Genuine Carbon Fiber |
| Finish | Matte Black |
| Item Weight | 3.17 ounces |
| Product Dimensions | 11.61 x 4.13 x 1.18 inches |
| Country of Origin | China |
Warranty and Support
For information regarding product warranty, returns, or technical support, please contact Bevinsee directly through their official channels or visit their store page. Specific warranty terms and conditions may vary.
Bevinsee Store: https://www.amazon.com/stores/Bevinsee/page/0EF33807-1E80-42AA-84F3-8DB6CFEC2922