Important Safety Information
Please read and understand all instructions and safety warnings before assembly and use of this product. Failure to follow these instructions may result in injury or product damage.
- Do not attempt to lift or move the box spring when it is fully assembled.
- Always follow the assembly instructions carefully to prevent instability or collapse.
- Be cautious of sharp edges and the folding design during assembly and use.
- Regularly inspect the box spring for any signs of wear or damage.
- Do not exceed the maximum weight capacity of 3500 lbs.
Package Contents
Verify that all components are present before beginning assembly.
- Box Spring Frame Components
- Fabric Cover
- Installation Manual
- Screws
- Wrench
Setup and Assembly
The MAF King Size Box Spring features a foldable design for easier setup. It is recommended that two adults assemble this product.
Tools Required:
- Included Wrench
- (Optional) Power screwdriver for faster assembly
Assembly Steps:
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, flat surface. Ensure all listed components are present.
- Unfold the Frame: The box spring frame comes in a folded configuration. Gently unfold the sections as shown in the diagram below. Ensure the triangular support designs lock into place.
- Secure Connections: Align the frame sections and secure them using the provided screws and wrench. Ensure all connections are tightened securely to prevent wobbling or noise.
- Install Slats: Place the metal slats into their designated positions on the frame. The U-shaped groove design helps secure each pole and support frame.
- Apply Fabric Cover: Once the frame is fully assembled and stable, carefully place the removable fabric cover over the box spring. The cover is designed for easy application and removal.
Figure 1: Assembly Steps for the MAF Box Spring.
Figure 2: Foldable Design and Easy Assembly Overview.
Figure 3: Key Structural Features: Round Corners, Triangular Support, and U-Shaped Grooves.
Operating Instructions
The MAF Box Spring is designed to provide stable support for your mattress. It can be used with various mattress types, including innerspring, memory foam, and latex mattresses.
- Placement: Position the assembled box spring on a compatible bed frame or directly on the floor if desired. Ensure it is level and stable.
- Mattress Placement: Carefully place your mattress on top of the box spring. The box spring is designed to support mattresses up to 80"L x 76"W.
- Weight Capacity: The box spring is engineered to support up to 3500 lbs. Do not exceed this weight limit to maintain structural integrity and safety.
- Noise Reduction: The U-shaped groove design and seamless welding are intended to prevent structural distortion and squeaks, providing a quiet sleeping environment.
Figure 4: Proper Layering of Bed Components.
Maintenance and Care
Proper maintenance ensures the longevity and performance of your MAF Box Spring.
- Cleaning the Cover: The fabric cover is removable and washable. Remove it from the frame for cleaning as needed. Follow care instructions on the cover label if available, or wash with mild detergent and cold water, then air dry.
- Frame Cleaning: Wipe the metal frame with a dry cloth to remove dust and debris. Avoid using harsh chemicals or abrasive cleaners.
- Regular Inspection: Periodically check all screws and connections to ensure they remain tight. Re-tighten if necessary. Inspect the frame for any signs of bending, cracks, or damage.
- Moving the Box Spring: If you need to move the box spring, it is recommended to disassemble it first, especially if moving through narrow doorways or stairs, to prevent damage to the product or injury.
Troubleshooting
If you encounter any issues with your MAF Box Spring, refer to the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Squeaking Noise | Loose connections or uneven placement. | Ensure all screws are tightly secured. Verify the box spring is placed on a flat, level surface. The U-shaped groove design is intended to minimize noise; if squeaking persists, re-check assembly. |
| Instability/Wobbling | Incomplete assembly or damaged components. | Re-check all assembly steps, ensuring triangular supports are engaged and all fasteners are tight. Inspect for any bent or damaged parts. |
| Mattress Sagging | Exceeded weight capacity or improper mattress support. | Ensure the combined weight of users and mattress does not exceed 3500 lbs. Verify the mattress is compatible with a box spring. |
Specifications
| Feature | Detail |
|---|---|
| Brand | MAF |
| Model Number | MAF-MT33-10K |
| Size | King |
| Product Dimensions | 78.8"L x 75.5"W x 10"H |
| Compatible Mattress Size | 80"L x 76"W |
| Special Feature | Foldable Design, Round Corner Design, Triangular Support, U-Shaped Groove Design |
| Finish Type | Powder Coated |
| Included Components | Box Spring Frame, Fabric Cover, Installation Manual, Screws, Wrench |
| Product Care Instructions | Wipe with Dry Cloth, Removable and Washable Fabric Cover |
| Assembly Required | Yes |
| Ground To Item Distance | 10 Inches |
| Item Weight | 49.1 pounds |
| Maximum Weight Capacity | 3500 lbs |
Figure 5: MAF Box Spring Size Chart.
Warranty and Support
Specific warranty details for the MAF Box Spring are not provided within this manual. For warranty information, please refer to the product packaging or contact MAF customer support directly.
For further assistance, questions, or to report any issues, please visit the official MAF store or contact their customer service department.
