1. Introduction
Thank you for choosing the LEKATO Yellow Comp Mini Compressor Pedal. This pedal is designed to provide classic optical compression for electric guitar and bass, featuring true bypass, EQ, and volume adjustments in a compact, portable form factor. This manual provides essential information for the proper setup, operation, and maintenance of your pedal.
2. Product Overview
The LEKATO Yellow Comp pedal offers precise control over your instrument's dynamics and tone. Its robust aluminum alloy casing ensures durability.
2.1 Controls and Features
- VOL Knob: Adjusts the overall output level of the effect.
- EQ Knob: Controls the tone brightness frequency response curve, allowing for fine-tuning of high and low frequencies.
- COMP Knob: Adjusts the amount of compression applied to the signal.
- True Bypass Footswitch: Engages or disengages the effect. When disengaged, the signal passes through without alteration, preserving your original tone.
- LED Indicator: Illuminates when the effect is active.
- DC IN Jack: For connecting a 9V DC power adapter (center negative).
- Input Jack (IN): 1/4-inch mono input for your instrument.
- Output Jack (OUT): 1/4-inch mono output to your amplifier or next pedal.




3. Setup
Follow these steps to connect your LEKATO Yellow Comp pedal to your instrument and amplifier.
- Power Connection: Connect a standard 9V DC power adapter (center negative, not included) to the DC IN jack on the top of the pedal. Ensure the power supply meets these specifications to prevent damage.
- Instrument Connection: Connect your electric guitar or bass to the IN jack on the right side of the pedal using a 1/4-inch mono instrument cable.
- Amplifier Connection: Connect the OUT jack on the left side of the pedal to your amplifier or the input of another effect pedal using a 1/4-inch mono instrument cable.
- Power On: Once all connections are secure, power on your amplifier and then the pedal (if using a switched power supply).


4. Operating Instructions
The Yellow Comp pedal is designed for intuitive operation. Experiment with the controls to find your desired sound.
- Engaging the Effect: Press the footswitch to activate the compressor. The LED indicator will light up.
- Adjusting Compression (COMP Knob): Turn the COMP knob clockwise to increase the amount of compression, resulting in a more sustained and focused sound. Turn it counter-clockwise for less compression.
- Adjusting Volume (VOL Knob): Use the VOL knob to match the output level of the compressed signal to your unprocessed signal, or to boost it for solos.
- Adjusting Tone (EQ Knob): The EQ knob allows you to brighten or darken your compressed tone. Turn it clockwise to add high frequencies for more presence, or counter-clockwise to reduce them for a warmer sound.
- True Bypass: When the effect is disengaged (LED off), the pedal operates in true bypass mode, ensuring your instrument's signal remains unaffected.

5. Maintenance
Proper care will ensure the longevity and optimal performance of your pedal.
- Cleaning: Use a soft, dry cloth to clean the pedal's surface. Avoid abrasive cleaners or solvents.
- Storage: Store the pedal in a dry environment, away from extreme temperatures and direct sunlight. Disconnect power when not in use for extended periods.
- Power Supply: Always use a regulated 9V DC, center-negative power supply. Incorrect power can damage the unit.
- Cables: Ensure all instrument cables are in good condition to prevent signal loss or noise.

6. Troubleshooting
If you encounter issues with your pedal, refer to the following common solutions:
- No Sound:
- Check all cable connections (instrument to IN, OUT to amplifier).
- Ensure the 9V DC power adapter is correctly connected and functioning.
- Verify your instrument and amplifier are working correctly.
- Excessive Noise/Hum:
- Ensure you are using a high-quality, regulated 9V DC power supply.
- Check for faulty instrument cables.
- Try isolating the pedal from other pedals or power sources to identify interference.
- Effect Not Engaging:
- Confirm the power supply is connected and working.
- Press the footswitch firmly; the LED should illuminate when the effect is active.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | M0034 |
| Item Weight | 5.9 ounces (167 grams) |
| Dimensions (L x W x H) | 4.45 x 2.4 x 2.05 inches (11.3 x 6.1 x 5.2 cm) |
| Body Material | Aluminum Alloy |
| Hardware Interface | 1/4-inch Audio Jacks |
| Signal Format | Analog |
| Power Source | DC 9V (Center Negative, Adapter Not Included) |
| Voltage | 9 Volts (DC) |
| Current Draw | 10mA |
| Input Impedance | 470k Ohms |
| Output Impedance | 1k Ohms |
| Audio Output Effects | Compression |

8. Safety Information
- Do not disassemble or modify the pedal. This may cause malfunction or electric shock.
- Do not expose the unit to water, moisture, or excessive humidity.
- Avoid operating the pedal in direct sunlight or near heat sources.
- Use only the specified power supply (9V DC, center negative).
- Keep out of reach of children.
9. Warranty and Support
LEKATO products are designed for reliability and performance. For specific warranty details, please refer to the warranty card included with your product or visit the official LEKATO website. If you require technical assistance or have questions regarding your Yellow Comp pedal, please contact LEKATO customer support through their official channels.