Introduction
This user manual provides essential information for the proper use and care of your LinkSun Blood Glucose Test Strips and Lancets Kit. This kit is designed to be used with compatible LinkSun/Bioland G-425-1, G-425-2V, and G-425-3 glucose meters (meter not included). Please read this manual thoroughly before use to ensure accurate results and safe operation.
Image: The LinkSun Blood Glucose Test Strips and Lancets Kit, showing the main box, two vials of test strips, and two boxes of sterile lancets.
Product Overview
The LinkSun Blood Glucose Test Strips and Lancets Kit provides the necessary consumables for blood glucose monitoring. The kit includes:
- Blood Glucose Test Strips: Designed for rapid and accurate blood glucose readings.
- Sterile Lancets: Ultra-thin needles for comfortable blood sampling.
Image: A banner illustrating the LinkSun Test Strips and Lancets Kit, highlighting it as a 200-piece value pack.
Compatibility
These test strips and lancets are specifically designed to be fully compatible with the following LinkSun/Bioland blood glucose meters:
- G-425-1 (G-666B)
- G-425-2V
- G-425-3 (G-427B)
- G-427B
Ensure your glucose meter is one of the compatible models for accurate readings. The glucose meter is not included in this kit and must be purchased separately.
Image: A visual representation of various compatible LinkSun/Bioland glucose meters (G-425-3, G-425-2V, G-425-1, G-427B).
Image: A banner emphasizing compatibility with LinkSun or Bioland brand meters, showing several meter models.
Setup
Before performing a blood glucose test, ensure you have the following items ready:
- LinkSun/Bioland Glucose Meter (compatible model)
- LinkSun Blood Glucose Test Strip
- LinkSun Sterile Lancet
- Lancing Device (usually comes with the meter)
- Alcohol swab (optional, for cleaning the test site)
Wash your hands thoroughly with soap and warm water, then dry them completely before handling any testing supplies.
Operating Instructions: How to Perform a Blood Glucose Test
Follow these steps for accurate blood glucose testing:
- Prepare the Lancing Device:
Insert a new LinkSun lancet into your lancing device until it clicks into place. Twist off the protective cap of the lancet to expose the needle. Adjust the depth setting on your lancing device by twisting the cap back on to your desired penetration level. Refer to your lancing device's manual for specific instructions on setting the depth.
- Insert the Test Strip:
Remove a test strip from its vial and immediately close the vial cap tightly. Insert the test strip into the test strip port of your glucose meter. The meter should turn on automatically and display a symbol indicating it is ready for a blood sample.
Image: A diagram illustrating the components of the test strip (absorbent hole, confirm window, handheld area, induction area) and how to insert it into the meter.
- Obtain a Blood Sample:
Hold the lancing device firmly against the side of your fingertip. Press the release button to prick your finger. Gently squeeze your finger until a small drop of blood forms. Do not smear the blood.
Image: A hand holding a glucose meter with a test strip inserted, showing a small blood sample being drawn onto the strip. Highlights fast test time (5 seconds) and small blood sample volume (0.7µL).
- Apply Blood to Test Strip:
Touch the tip of the test strip to the blood drop. The blood will be automatically drawn into the strip. The meter will begin counting down once enough blood has been applied.
- Read Results:
Your blood glucose result will appear on the meter's display within approximately 5 seconds.
- Dispose of Used Supplies:
Carefully remove the used test strip from the meter and dispose of it properly. Eject the used lancet from the lancing device and dispose of it in a puncture-resistant container (sharps container). Do not reuse test strips or lancets.
Image: A six-step visual guide demonstrating the process of preparing the lancing device, inserting the test strip, and applying blood for testing.
Test Strip Details
LinkSun Blood Glucose Test Strips are designed for ease of use and accuracy:
- No Coding Required: Eliminates manual coding, reducing potential errors and simplifying the testing process.
- Fast Results: Provides accurate readings in approximately 5 seconds.
- Small Blood Sample: Requires only 0.7µL of blood, contributing to a less painful experience.
- Self-Testing: Suitable for personal use, promoting safe and hygienic testing by avoiding cross-infection.
- Shelf Life: Stable for 24 months unopened. Discard 3 months after opening the vial.
Image: A banner providing detailed information about LinkSun Test Strips, including no coding, 0.7µL blood sample, 5-second read time, suitability for self-testing, and discard period after opening.
Image: A layered diagram explaining the accurate and stable technology of the test strip, showing protection, hydrophilic layer, glucose oxidase, bioelectrode, and PET base.
Lancet Details
LinkSun 30G Lancets are designed for minimal discomfort:
- 30 Gauge Ultra-Thin Needle: Minimizes pain and creates a small wound for fast healing.
- Gamma Sterilized: Ensures safety and hygiene for each use.
- Protective Cap: Each lancet comes with a twist-off protective cap.
- Safety Shield Design: Allows for safe re-capping and disposal after use.
- Long-lasting: Up to 5 years shelf life.
Image: A detailed diagram of a 30 gauge safety lancet, showing its twist-off protective cap, 0.3mm micro lancet, and one-button lancet rejection feature. Highlights small wound and nearly painless testing.
Image: A comparison illustrating the painless blood testing experience with LinkSun lancets (tri-beveled tip) versus other lancets, showing minimized skin trauma.
Image: A banner providing detailed information about LinkSun 30G Lancets, including painless testing, sterilization, safety shield design, and long shelf life.
Image: A banner depicting a couple using a lancing device, with a large graphic of a lancet and a shield, emphasizing the safety of the product.
Precautions
Adhere to the following precautions for safe and effective use:
- Before use, carefully read the instruction manual provided in the package and operate the device as directed.
- Do not use expired test strips or lancets.
- Test strips and lancets are for single-use only. Reuse or sharing between multiple users is prohibited.
- Use test strips and lancets right after opening. Discard if: Packaging is damaged, Needle tip is bent/broken, Protective cap is missing.
- Remove the lancet from the lancing device immediately after use. Close the cap tightly after removing the test strip or when not in use.
- Storage conditions: Temperature: 4°C to 40°C (freezing prohibited), Humidity: <85% RH.
- Avoid exposing test strips and lancets to direct sunlight for extended periods.
- Do not bend test strips or subject them to heavy pressure.
Image: A banner clearly listing eight important precautions for the use and storage of blood glucose test strips and lancets.
Maintenance and Storage
Proper maintenance and storage are crucial for the longevity and accuracy of your testing supplies:
- Always store test strips and lancets in their original vials/boxes with caps tightly closed.
- Store at temperatures between 4°C and 40°C (39°F and 104°F). Do not freeze.
- Keep away from direct sunlight, heat, and moisture.
- After opening a vial of test strips, use them within 3 months. Write the discard date on the vial label.
- Dispose of used test strips and lancets in a biohazard sharps container according to local regulations.
Specifications
| Feature | Detail |
|---|---|
| Product Name | Blood Glucose Test Strips & Lancets Kit |
| Brand | LinkSun |
| Model Number | G-425-1S (for kit components) |
| Compatible Meters | LinkSun/Bioland G-425-1, G-425-2V, G-425-3 |
| Test Strip Type | Blood Glucose |
| Blood Sample Volume | 0.7 µL |
| Test Time | Approx. 5 seconds |
| Lancet Gauge | 30 Gauge |
| Number of Pieces (Kit) | 100 Test Strips + 100 Lancets (200 total) |
| Storage Temperature | 4°C to 40°C (39°F to 104°F) |
| Storage Humidity | <85% RH |
| Manufacturer | Bioland |
Troubleshooting
This section addresses common issues you might encounter with the test strips and lancets. For issues related to your glucose meter, please refer to your meter's specific user manual.
| Problem | Possible Cause | Solution |
|---|---|---|
| Meter does not turn on after inserting strip. | Strip inserted incorrectly; meter battery low; strip expired or damaged. | Ensure strip is fully inserted in the correct direction. Check meter battery. Use a new, unexpired strip. |
| Insufficient blood sample. | Not enough blood applied; blood applied too slowly; lancing depth too shallow. | Ensure a sufficient blood drop forms before applying. Apply blood quickly to the strip. Adjust lancing device depth if needed. |
| Error message on meter (e.g., "E-1", "E-2"). | Specific error codes vary by meter; often indicates strip issue, temperature, or meter malfunction. | Refer to your glucose meter's user manual for specific error code meanings and solutions. Ensure strips are stored correctly and not expired. |
| Pain during lancing. | Lancing depth too deep; incorrect lancing technique. | Adjust lancing device to a shallower depth. Use the side of the fingertip, not the pad. Ensure hands are warm to promote blood flow. |
| Test strips stuck together in vial. | Humidity or manufacturing variation. | Gently separate them. If separation damages the strip, discard and use a new one. Store in a cool, dry place. |
Customer Support
For further assistance or inquiries regarding your LinkSun Blood Glucose Test Strips and Lancets Kit, please contact LinkSun customer support through the retailer where you purchased the product or refer to the contact information provided on the product packaging.
Manufacturer: Bioland
