Introduction
This manual provides essential instructions for the safe and efficient operation, installation, and maintenance of your MSpa Round Inflatable Bubble Massage Spa, Model F-DU063W. Please read this manual thoroughly before setting up and using your spa to ensure proper function and longevity of the product. Keep this manual for future reference.
Important Safety Instructions
WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. Always supervise children. This spa is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Always connect the spa to a grounded outlet.
- Do not operate the spa if the water temperature is above 104°F (40°C).
- Consult a doctor before use if you are pregnant, have health conditions, or are on medication.
- Do not use electrical appliances near the spa.
- Ensure the spa is placed on a flat, stable surface capable of supporting its weight when filled.
- Regularly check the water quality and maintain proper chemical balance.
- Always use the spa cover when not in use to prevent unsupervised access and heat loss.
Package Contents
Before beginning assembly, ensure all components listed below are present and undamaged. If any parts are missing or damaged, do not proceed with assembly and contact customer support.
- Inflatable Spa Body (Woodgrain finish)
- External Control Box with Pump and Heater
- Standard Spa Cover (Black)
- Energy-Efficient Spa Cover (Black)
- Filter Cartridge(s)
- Inflation Hose
- Drainage Hose Adapter
- Repair Kit
- Instruction Manual (This document)
Setup Instructions
1. Site Selection and Preparation
Choose a flat, level surface free of sharp objects. The area must be able to support the weight of the filled spa (approximately 245 gallons of water plus occupants). Ensure there is adequate drainage and access to a grounded electrical outlet.
2. Inflation
- Unfold the spa body and lay it flat on the prepared surface.
- Connect the inflation hose to the air valve on the spa body and to the inflation port on the control box.
- Plug in the control box and press the "Bubble" button to begin inflation.
- Inflate until the spa walls are firm to the touch, but not over-inflated. Do not use an air compressor.
- Disconnect the inflation hose and securely close the air valve.
3. Control Box Connection
Connect the control box to the spa body's water inlet and outlet ports. Ensure all connections are tight to prevent leaks.
4. Water Filling
Fill the spa with fresh water using a garden hose. Fill to the recommended water level indicated on the spa's interior wall. Do not overfill.
5. Filter Installation
Install the filter cartridge(s) into the filter housing(s) inside the spa. Ensure they are securely twisted into place.
Operating Instructions
1. Control Panel and MSpa Mobile App
The spa can be controlled via the integrated control panel on the external unit or through the MSpa mobile application. The app provides full control over spa functions from your smartphone.
2. Heating Function
Press the "Heater" button on the control panel or app to activate the heating system. The water temperature will increase at a rate of approximately 1.8-2°F per hour, up to a maximum of 104°F (40°C). The display will show the current water temperature.
3. Bubble Massage System
Activate the 138 Air Jets Massage System by pressing the "Bubble" button. The system offers 3 variable bubble speeds for a customized experience. Press the button repeatedly to cycle through speeds or turn off.
4. Smart Filtration
The smart filtration system automatically runs to keep your water clean. Ensure filter cartridges are regularly cleaned or replaced for optimal performance.
5. Anti-Icing System
The anti-icing system automatically activates when the water temperature drops below a certain threshold, preventing freezing and protecting internal components. This feature is designed for use in cold weather conditions.
6. Heating Timer
Utilize the heating timer function to schedule when the spa heater turns on. This allows you to pre-heat the spa to your desired temperature before use, saving energy and ensuring it's ready when you are.
Maintenance
1. Water Chemistry
Regularly test and adjust the spa water chemistry (pH, alkalinity, sanitizer levels) according to recommended guidelines. Improper water balance can damage the spa and cause skin irritation.
2. Filter Cleaning and Replacement
Clean filter cartridges weekly by rinsing them with a garden hose. Replace cartridges every 1-2 months, or more frequently with heavy use, to maintain efficient filtration.
3. Draining and Cleaning
Drain and refill the spa water at least once every two months. When draining, clean the interior surface of the spa with a soft cloth and mild, non-abrasive cleaner. Rinse thoroughly before refilling.
4. Spa Cover Care
Always use the spa cover when the spa is not in use. The included energy-efficient cover significantly improves heat retention, saving up to 50% on energy. Clean covers regularly with a mild soap and water solution. Inspect for damage and repair as needed.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Spa not heating | Heater not activated, low water level, dirty filter, ambient temperature too low. | Ensure heater is on. Check water level and add water if necessary. Clean or replace filter. Use energy-efficient cover. |
| No bubbles | Bubble function not activated, air blower malfunction. | Press the "Bubble" button. If issue persists, contact customer support. |
| Water cloudy | Dirty filter, improper water chemistry, heavy use. | Clean or replace filter. Test and adjust water chemistry. Shock treat the water. |
| Error code on display | Specific system issue (e.g., sensor error, flow error). | Refer to the specific error code section in the full manual (if available) or contact customer support with the code. |
Specifications
| Feature | Detail |
|---|---|
| Brand | MSpa |
| Model Name | F-DU063W |
| Color | Black (Spa body with woodgrain finish) |
| Product Dimensions | 68"L x 68"W x 26"H |
| Material | Vinyl |
| Capacity | 245 Gallons |
| Number of Air Jets | 138 |
| Seating Capacity | Up to 6 people |
| Max Water Temperature | 104°F (40°C) |
| Heating Rate | 1.8-2°F per hour |
| Assembly Required | No (referring to complex assembly, inflation is required) |
| UPC | 193802381740 |
Warranty and Customer Support
MSpa products are manufactured to high-quality standards and are backed by a limited warranty. For specific warranty details, please refer to the warranty card included with your product or visit the official MSpa website.
If you encounter any issues or have questions regarding your MSpa Round Inflatable Bubble Massage Spa, please contact MSpa customer support. Have your model number (F-DU063W) and purchase information ready when contacting support.
MSpa Official Website: www.mspa.com
