JUMMICO Gaming Chair Instruction Manual

Introduction

This manual provides comprehensive instructions for the assembly, operation, and maintenance of your JUMMICO Gaming Chair. Please read this manual thoroughly before assembly and use to ensure proper function and safety.

Important Safety Information

• Ensure all components are securely fastened before use.
• Do not stand on the chair.
• Do not use the chair if any parts are damaged or missing.
• Keep children away from moving parts during adjustment.
• Maximum weight capacity: 300 lbs.

Package Contents

Before beginning assembly, verify that all parts listed below are present and undamaged:

• 1 x Backrest
• 1 x Seat
• 1 x Footrest
• 1 x Hardware Fitting Bag (containing screws, tools, etc.)
• 1 x Instructions Manual (this document)
• 1 x Headrest Pillow
• 1 x Lumbar Support Pillow with Massage Function
• 1 x Gas Lift Cylinder
• 1 x Base (Star Base)
• 5 x Casters

Note: Some smaller components may be pre-attached to larger parts. Refer to the assembly instructions for detailed identification.

Assembly Instructions

Follow these steps carefully to assemble your JUMMICO Gaming Chair. It is recommended to assemble the chair on a soft, clean surface to prevent damage.

Step 1: Attach Casters to Base

Insert the five casters into the holes at the end of each leg of the star base. Push firmly until they click into place.

Image: Illustration showing the assembly of the chair's star base with casters.

Step 2: Install Gas Lift Cylinder

Place the gas lift cylinder into the center hole of the assembled star base. Ensure it sits securely.

Step 3: Attach Mechanism to Seat

Align the seat mechanism with the pre-drilled holes on the underside of the seat cushion. Secure it using the provided screws from the hardware bag. Ensure the front of the mechanism faces the front of the seat.

Step 4: Connect Backrest to Seat

Attach the backrest to the seat using the metal brackets and screws. Ensure a firm connection.

Image: Diagram illustrating the connection points for the backrest and seat.

Step 5: Place Assembled Seat onto Gas Lift

Carefully place the assembled seat and backrest onto the gas lift cylinder, ensuring the center hole of the mechanism aligns with the top of the gas lift. Press down firmly to secure.

Step 6: Attach Footrest

Slide the footrest into its designated slots beneath the seat. Ensure it can extend and retract smoothly.

Step 7: Install Headrest and Lumbar Support Pillows

Attach the headrest pillow to the top of the backrest using its straps. Position the lumbar support pillow at your preferred height on the lower backrest, securing it with its straps.

Image: A complete view of the JUMMICO gaming chair, highlighting the headrest and lumbar support pillows.

Operating Instructions

1. Seat Height Adjustment

To adjust the seat height, locate the lever on the right side beneath the seat. While seated, pull the lever up to lower the seat. To raise the seat, stand up and pull the lever up. Release the lever at the desired height.

Image: Visual guide for seat height adjustment, indicating the lever's function.

2. Backrest Recline Function

To recline the backrest, pull the lever on the left side beneath the seat. Lean back to the desired angle (up to 135 degrees) and release the lever to lock it in place. To return to an upright position, pull the lever again and lean forward.

Image: Visual guide for backrest recline adjustment, illustrating the range of motion.

3. Footrest Operation

To use the footrest, pull it out from beneath the seat. Extend it to your preferred length. To retract, push it back under the seat until it is fully stored.

Image: Illustration of the adjustable footrest mechanism and its extension.

4. Massage Lumbar Support

The lumbar support pillow features a massage function. Connect the USB cable from the pillow to a compatible USB power source (e.g., computer, power bank, USB wall adapter). The massage function will activate, providing gentle vibration to the lower back area.

Image: Close-up of the massage lumbar support, indicating its features and power connection.

5. 360° Swivel Function

The chair is designed with a 360-degree swivel function, allowing for full rotation without moving the base. This feature is always active.

Maintenance

• Cleaning: Wipe the chair with a soft, damp cloth. For stubborn stains on the PU leather, use a mild leather cleaner. Avoid harsh chemicals or abrasive cleaners.
• Fasteners: Periodically check all screws and bolts to ensure they are tight. Re-tighten if necessary to maintain stability and prevent loosening, especially for armrests.
• Casters: Keep casters clean and free of debris (hair, dust) to ensure smooth movement.
• Storage: Store the chair in a dry environment, away from direct sunlight and extreme temperatures.

Troubleshooting

Specifications

Image: The JUMMICO gaming chair integrated into a typical gaming environment, showcasing its design and functionality.

Warranty and Customer Support

JUMMICO is committed to providing quality products and excellent customer service. For any questions regarding assembly, operation, missing parts, or warranty claims, please contact JUMMICO customer support.

Please retain your purchase receipt for warranty purposes.