Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your HammerHead Showers Solid Metal 16 Inch Extended Shower Arm. This product is designed to provide an optimal overhead rain shower experience with its durable, solid metal construction.
Safety Information
- Ensure all water supply is turned off before beginning installation.
- Wear appropriate personal protective equipment, such as safety glasses, during installation.
- Do not overtighten connections, as this may damage threads or components.
- If you are unsure about any step, consult a qualified plumber.
Package Contents
Verify that all components are present before beginning installation:
- 1 x Solid Metal 16 Inch Extended Shower Arm
- 1 x Brass Flange
- 1 x Set Screw
- 1 x Allen Wrench
- 1 x Thread Seal Tape
Setup and Installation
Follow these steps for proper installation of your shower arm:
- Prepare the existing shower pipe: Ensure the existing shower pipe extending from the wall is clean and free of debris. Turn off the main water supply to the shower.
- Apply Thread Seal Tape: Wrap the provided thread seal tape clockwise around the threaded end of the shower arm that will connect to the wall pipe. Apply 3-5 layers for a secure, leak-free seal.
- Thread Shower Arm into Wall: Carefully thread the shower arm into the existing shower pipe in the wall. Hand-tighten first, then use the provided Allen wrench inserted into the shower arm outlet for leverage to tighten securely. Ensure the arm is oriented correctly for your shower head.
- Slide Flange Over Shower Arm: Slide the brass flange over the shower arm, pushing it flush against the wall. The flange is designed to cover the wall opening for a finished appearance.
- Secure Flange with Set Screw: Locate the small set screw on the flange. Use the Allen wrench to tighten this screw, securing the flange firmly to the shower arm and preventing it from sliding or spinning.
- Attach Shower Head: Apply thread seal tape to the threaded end of the shower arm where your shower head will attach. Thread your rain shower head onto the arm and tighten securely.
- Test for Leaks: Turn the main water supply back on and check all connections for leaks. If leaks occur, turn off the water, re-apply thread seal tape, and re-tighten connections.
Image: Step-by-step visual guide for installing the shower arm, showing tape application, threading into the wall, and securing the flange.
Image: Detail showing the locking set screw on the flange, which prevents movement and ensures a neat finish against the wall.
Operating Instructions
Once installed, the HammerHead Showers 16 Inch Extended Shower Arm functions as a fixed extension for your rain shower head. It positions the shower head further from the wall and directly overhead, enhancing the rainfall effect. Operate your shower as usual using your shower valve controls.
Image: A visual representation of the shower arm in use, extending a rain shower head overhead for an immersive experience.
Maintenance
To ensure the longevity and appearance of your shower arm:
- Cleaning: Clean the shower arm and flange regularly with a soft cloth and mild, non-abrasive soap.
- Avoid Harsh Chemicals: Do not use abrasive cleaners, scouring pads, or chemical solvents, as these can damage the finish.
- Inspect Connections: Periodically check the connections for any signs of loosening or leaks. Re-tighten if necessary.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Leaks at wall connection | Insufficient thread seal tape or loose connection. | Turn off water, remove arm, re-apply 3-5 layers of thread seal tape, and re-tighten securely. |
| Flange slides down the arm | Set screw not tightened. | Tighten the set screw on the flange using the provided Allen wrench. |
| Shower arm feels unstable or sags | Inadequate support from in-wall plumbing or improper tightening. | Ensure the shower arm is fully threaded and tightened. If the in-wall plumbing is not secure, professional reinforcement may be required. |
Specifications
- Brand: HammerHead Showers
- Model Number: 16-J-ARM
- Material: Solid Metal (Stainless Steel and Brass)
- Finish Type: Chrome
- Installation Type: Wall Mounted
- Arm Length: 16 Inches (406.4mm)
- Flange Depth: 0.346 Inches (8.8mm)
- Flange Diameter: 2.5 Inches (63.5mm)
- Thread Size: 1/2" NPT (National Pipe Taper)
- Compatibility: Fits all standard rain shower heads in the US and Canada.
Image: Technical drawing illustrating the key dimensions of the 16-inch shower arm, including length, flange size, and thread type.
Warranty
HammerHead Showers products are built to last and are backed by a lifetime warranty. This warranty covers defects in material and workmanship under normal use and service. For specific warranty details and claims, please refer to the official HammerHead Showers website or contact customer support.
Support
For further assistance, technical support, or to inquire about replacement parts, please visit the HammerHead Showers official website or contact their customer service department. Contact information can typically be found on the product packaging or the brand's online presence.
