ELEGOO Mercury Plus 3.0 Wash and Cure Machine User Manual

Introduction

The ELEGOO Mercury Plus 3.0 is an integrated wash and cure machine designed for post-processing resin 3D prints. It combines washing and UV curing functions into a single unit, streamlining the workflow for resin printing. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your device.

Safety Information

• Always operate the machine in a well-ventilated area.
• Wear appropriate personal protective equipment (PPE), including gloves and eye protection, when handling uncured resin or cleaning agents like Isopropyl Alcohol (IPA).
• Keep the machine away from direct sunlight and heat sources.
• Ensure the UV-blocking cover is in place during curing to prevent UV exposure. The machine is designed to pause operation if the cover is removed during curing.
• Do not ingest resin or cleaning agents. In case of accidental ingestion, seek medical attention immediately.
• Dispose of waste resin and contaminated cleaning agents according to local regulations.
• Keep out of reach of children and pets.

Package Contents

Verify that all items listed below are included in your package:

• ELEGOO Mercury Plus 3.0 Wash and Cure Machine
• Washing Bucket (7.5L capacity)
• Curing Turntable
• Washing Basket
• Adjustable Support (x2)
• Power Adapter
• User Manual (this document)
• Tools (specific tools may vary)

Image: Overview of the ELEGOO Mercury Plus 3.0 package contents, including the main unit, washing bucket, curing turntable, washing basket, adjustable supports, power adapter, manual, and tools.

Product Overview

The Mercury Plus 3.0 features a combined design for efficient post-processing. It includes a large washing capacity and an enhanced curing area.

Image: The ELEGOO Mercury Plus 3.0 machine shown alongside its transparent washing bucket, illustrating its compact design and separate components for washing and curing.

Setup

1. Unpacking: Carefully remove all components from the packaging.
2. Placement: Place the machine on a stable, level surface in a well-ventilated area, away from direct sunlight.
3. Power Connection: Connect the power adapter to the machine and then to a power outlet.
4. Prepare Washing Solution: Fill the washing bucket with an appropriate cleaning agent, such as Isopropyl Alcohol (IPA) or water for water-washable resins. Do not exceed the MAX fill line (7.5L).

Operating Instructions

Washing Process

The Mercury Plus 3.0 offers two washing modes:

• With Washing Basket: For models removed from the build plate. Place the printed model directly into the washing basket.
• Suspended Washing: For washing models directly on the build plate. Attach the build plate to the adjustable support and suspend it in the washing bucket. This prevents direct contact with uncured resin.

1. Place the washing bucket with the cleaning agent onto the machine base.
2. Insert the washing basket with your model(s) or suspend the build plate with the model(s) into the bucket.
3. Close the lid of the washing bucket securely.
4. Select the "Wash" mode on the control panel.
5. Adjust the washing time using the timer controls (up to 30 minutes).
6. Press the Start button to begin the washing cycle. The machine will create a powerful vortex to clean the models.
7. Once the cycle is complete, carefully remove the models and allow them to dry.

Image: Illustration of the two washing modes: one showing models in a basket for direct washing, and another showing a build plate suspended for washing models still attached.

Image: A visual representation of the powerful vortex generated by the machine during the washing cycle, ensuring thorough cleaning of resin models.

Curing Process

1. Ensure the washing bucket is removed from the machine base.
2. Place the curing turntable onto the machine base.
3. Place your dried, washed model(s) on the center of the turntable.
4. Cover the machine with the UV-blocking cover.
5. Select the "Cure" mode on the control panel.
6. Adjust the curing time using the timer controls (up to 30 minutes).
7. Press the Start button to begin the curing cycle. The turntable will rotate, and UV lights will activate for 360-degree curing.
8. The machine will automatically pause if the UV cover is removed during operation.
9. Once the cycle is complete, remove the fully cured models.

Image: The ELEGOO Mercury Plus 3.0 in curing mode, showing UV lights illuminating a 3D printed model on a rotating turntable for uniform 360-degree curing.

Image: The orange UV-blocking cover placed over the ELEGOO Mercury Plus 3.0, highlighting its function in blocking 99.9% of UV light for user safety.

Maintenance

• Cleaning the Washing Bucket: Regularly clean the washing bucket and basket to remove resin residue. Use a soft cloth and cleaning agent.
• Replacing Cleaning Agent: Replace the cleaning agent (IPA/water) when it becomes heavily contaminated with resin. Filter used IPA to extend its life.
• Cleaning the Machine Exterior: Wipe the exterior of the machine with a soft, damp cloth. Avoid using abrasive cleaners.
• UV Lamp Maintenance: Keep the UV lamps and Fresnel lens clean for optimal curing performance.

Troubleshooting

Specifications

Compatibility

The ELEGOO Mercury Plus 3.0 is compatible with resin 3D printers featuring LCD screens of 10 inches and smaller, including but not limited to:

• ELEGOO Mars series: Mars 2, Mars 2 Pro, Mars 3, Mars 3 Pro, Mars 4, Mars 4 Ultra, Mars 4 Max, Mars 4 DLP, Mars 5, Mars 5 Ultra
• ELEGOO Saturn series: Saturn, Saturn S, Saturn 8K, Saturn 2, Saturn 3, Saturn 3 Ultra, Saturn 4, Saturn 4 Ultra
• ELEGOO Jupiter

Image: The adjustable platform support mechanism, demonstrating its adaptability for different build plate sizes from various ELEGOO Mars and Saturn series printers.

Warranty and Support

Manufacturer Warranty: The product comes with a 1-year manufacturer warranty.

Technical Support: For technical assistance, troubleshooting, or warranty claims, please contact ELEGOO customer support. ELEGOO is committed to providing high-quality products and services.

You can visit the official ELEGOO store for more information and support resources: ELEGOO Store