1. Introduction
This manual provides instructions for the installation and use of the Yoursme W10324651 Drive Hub Kit. This kit is designed as a replacement drive block for the inner tub of various washing machine models.
The W10324651 Drive Hub Kit is compatible with a wide range of washing machine brands, including Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore. It replaces part numbers W10324651, 1877235, AH2581262, EA2581262, PS2581262, W10291415, W10291416, W10291417, W10528947, W10396887, W10528947VP, PS6012095, AP5665171, 2684908, and EAP6012095.
Proper installation of this drive hub kit can help resolve common washing machine issues such as unusual noise, water leakage, shaking and moving during operation, and problems with agitation or spinning.
Image 1.1: Overview of the W10324651 Washer Basket Drive Hub Kit components.
2. Package Contents
The W10324651 Drive Hub Kit includes the following components:
- Basket Driven Hub
- Drive Block Retainers
- 6 Screws
- 2 Wire Harness Holders
3. Safety Information
Before attempting any repairs or installations on your washing machine, please observe the following safety precautions:
- Disconnect Power: Always unplug the washing machine from the power outlet before beginning any work to prevent electrical shock.
- Water Supply: Turn off the water supply to the washing machine.
- Wear Protective Gear: Use appropriate personal protective equipment, such as gloves and safety glasses.
- Consult Professional: If you are unsure about any step or lack the necessary tools or experience, it is recommended to consult a qualified appliance repair technician.
- Original Manual: Refer to your washing machine's original service manual for specific disassembly and reassembly instructions for your model.
4. Installation Instructions
Follow these steps to install the W10324651 Drive Hub Kit. These are general guidelines; specific washer models may have variations. Always refer to your appliance's service manual for detailed instructions.
- Remove Old Driven Hub and Drive Block: Carefully disassemble the washing machine to access the inner tub and the existing driven hub and drive block. Remove these old components.
- Install New Drive Block onto Spin Tube: Place the new drive block component onto the spin tube of the washing machine.
- Install Driven Hub Using Screws: Position the new driven hub over the drive block and secure it using the provided screws. Ensure they are tightened appropriately.
- Install Tub Nut and Hand Tighten: Install the tub nut and hand tighten it to secure the assembly.
- Tighten Nut with Hammer and Wrench: Use a wrench to further tighten the tub nut. Lightly tap the wrench with a hammer to ensure a secure fit.
- Inspect Installation: Visually inspect all connections and components to ensure they are correctly installed and secure before reassembling the washing machine.
Image 4.1: Step-by-step installation process for the drive hub kit.
5. Operating
After successful installation of the W10324651 Drive Hub Kit and reassembly of your washing machine, the appliance should operate as intended. The new drive hub facilitates the proper rotation and agitation of the inner tub, ensuring efficient washing and spinning cycles. Conduct a test cycle without laundry to confirm proper function and absence of leaks or unusual noises.
6. Maintenance
The W10324651 Drive Hub Kit is constructed from durable aluminum and steel with a protective coating designed to resist corrosion, rust, and oxidation, ensuring a long service life. Regular maintenance of your washing machine, such as cleaning the tub and checking for any obstructions, will help prolong the life of all components, including the drive hub.
7. Troubleshooting
If you experience issues after installing the W10324651 Drive Hub Kit, consider the following:
- Unusual Noise/Shaking: Re-check the tightness of all fasteners, especially the tub nut. Ensure the drive hub and drive block are seated correctly. Verify that the washing machine is level.
- Water Leakage: Inspect all water connections and seals. Ensure the tub nut is sufficiently tightened.
- No Agitation/Improper Spinning: Confirm that the drive hub is fully engaged with the spin tube and that the drive block retainers are correctly installed. Ensure no foreign objects are obstructing the tub's movement.
If problems persist, it is advisable to consult a professional appliance repair technician.
Image 7.1: Common washing machine problems that the drive hub kit can help address.
8. Specifications
| Manufacturer | Yoursme |
| Part Number | YS-W10324651 |
| Item Weight | 8.3 ounces |
| Product Dimensions | 4 x 4 x 1 inches |
| Included Components | 1x Drive Hub Kit (Basket Driven Hub, Drive Block Retainers, 6 Screws, 2 Wire Harness Holders) |
Image 8.1: Product dimensions of the drive hub kit components.
9. Warranty and Support
This product comes with a 1-Year Warranty from the manufacturer, Yoursme. For warranty claims or technical support, please refer to the contact information provided with your purchase or visit the manufacturer's official website.
Always ensure you have your purchase details and model number (YS-W10324651) available when contacting support.