Locksworth 1.9 Cubic Feet Home Security Safe ET525 Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Locksworth 1.9 Cubic Feet Home Security Safe, Model ET525. Please read this manual thoroughly before using the safe to ensure proper function and security.

Image: The Locksworth 1.9 Cubic Feet Home Security Safe, featuring a black finish and electronic keypad with key override.

Safety Information

• Keep emergency keys in a secure location away from the safe and not inside it.
• Do not store the instruction manual inside the safe.
• Ensure the safe is securely mounted to prevent unauthorized removal.
• Replace batteries promptly when the low battery indicator appears to avoid lockout.
• Avoid exposing the safe to extreme temperatures or humidity.

Package Contents

Verify that all components are present in the package:

• 1 x Locksworth 1.9 Cubic Feet Security Safe
• 2 x Emergency Keys
• 2 x Expansion Bolts (Sets)
• 4 x AA Batteries
• 1 x User Manual

Setup

1. Battery Installation

1. Open the safe door using one of the emergency keys. Insert the key into the keyhole on the electronic panel and turn it clockwise. Rotate the knob to open the door.
2. Locate the battery compartment on the inside of the safe door.
3. Insert 4 AA batteries (included) into the compartment, ensuring correct polarity (+/-).
4. Close the battery compartment cover.

2. Setting Your Personal Passcode

1. With the safe door open, locate the red reset button on the inside of the door, near the hinge.
2. Press the reset button. You will hear two beeps, and the yellow "PROCEED" light on the keypad will illuminate.
3. Within 5 seconds, enter your desired 3-8 digit passcode on the keypad.
4. Press the "A" or "B" button to confirm your passcode. You will hear a confirmation beep, and the yellow light will turn off.
5. Test your new passcode with the door open before closing it. Enter your passcode, press "A" or "B", then turn the knob to ensure it retracts the bolts.

3. Mounting Instructions

The safe can be securely mounted to a floor, wall, or cabinet using the pre-drilled anchor points and expansion bolts.

1. Unlock the safe and open the door.
2. Identify the pre-drilled holes on the bottom or back of the safe.
3. Position the safe in your desired location and mark the drilling points on the floor or wall through the holes. Move the safe aside.
4. Drill pilot holes at the marked locations using an appropriate drill bit for your surface (wood, concrete, etc.).
5. Align the safe with the drilled holes. Insert the expansion bolts through the safe's holes and into the pilot holes.
6. Tighten the bolts securely using a wrench. Ensure the safe is firmly attached and cannot be easily moved.

Image: A visual guide illustrating the steps for securely mounting the safe to a wall or floor using expansion bolts.

Operating Instructions

1. Opening with Passcode

1. Enter your 3-8 digit personal passcode on the keypad.
2. Press the "A" or "B" button. The green "READY" light will illuminate, and you will hear a beep.
3. Within 5 seconds, turn the knob clockwise to open the safe door.

Image: The safe's control panel, detailing the knob, keypad, indicator lights, and key entry point for both passcode and key unlocking methods.

2. Opening with Emergency Key

The emergency key provides access if batteries are depleted or the passcode is forgotten.

1. Locate the keyhole cover on the electronic panel. Remove the cover.
2. Insert one of the emergency keys into the keyhole and turn it clockwise.
3. While holding the key turned, rotate the knob clockwise to open the safe door.
4. Once open, remove the key.

3. Alarm System

The safe features an audible alarm system for enhanced security:

• If an incorrect passcode is entered three times consecutively, the safe will alarm and lock for 20 seconds.
• If an incorrect passcode is entered three more times (total of six incorrect attempts), the safe will alarm and lock for 5 minutes.
• During an alarm state, the safe cannot be opened with the passcode. Use the emergency key to access the safe.

Maintenance

• Battery Replacement: Replace all four AA batteries when the "LO-BAT" indicator light illuminates on the keypad. Always replace all batteries at once with new, high-quality alkaline batteries.
• Cleaning: Wipe the safe's exterior with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish or electronic components.
• Key Storage: Store emergency keys in a secure, hidden location outside the safe. Do not store them inside the safe.
• Internal Shelf: The safe includes an adjustable/removable shelf. Ensure it is properly seated if used.

Image: The interior of the safe, demonstrating the adjustable shelf and ample storage space for various valuables.

Troubleshooting

Specifications

Image: Detailed external dimensions of the Locksworth safe, providing measurements for height, width, and depth.

Warranty and Support

For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official Locksworth website. Keep your purchase receipt as proof of purchase for warranty claims.

Locksworth Store: Visit the Locksworth Store on Amazon