Introduction
This manual provides essential information for the safe and effective use of your DotMod dot TANK MAX 0.15Ω Replacement Coils. Please read this manual thoroughly before use and retain it for future reference.
These coils are specifically designed for the DotMod dot TANK MAX, ensuring optimal performance and vapor production. Each pack contains 5 replacement coils.
Image: Retail packaging for the DotMod dot TANK MAX 0.15Ω replacement coils. The box is brown and black, featuring the DotMod logo, '0.15Ω (70-90w)', and 'dotCoil 5pcs'. An illustration of the coil is prominently displayed in the center.
Safety Information
WARNING:
- Keep out of reach of children and pets.
- Do not disassemble, modify, or attempt to repair the coils.
- Use only with compatible DotMod dot TANK MAX devices.
- Ensure proper installation to prevent leaks or damage.
- Dispose of used coils responsibly according to local regulations.
Setup and Installation
- Prepare your Tank: Ensure your DotMod dot TANK MAX is empty of e-liquid and disassembled.
- Remove Old Coil: Unscrew the base of the tank and carefully pull out the old coil.
- Prime the New Coil: Before installing, apply a few drops of e-liquid to the cotton wicking ports on the new 0.15Ω coil. This helps saturate the cotton and prevents dry hits.
- Install New Coil: Insert the new coil firmly into the tank base, ensuring it is seated correctly.
- Reassemble Tank: Screw the tank base back onto the tank securely.
- Fill Tank: Fill the tank with your preferred e-liquid.
- Allow to Soak: Let the tank sit for at least 5-10 minutes after filling to allow the e-liquid to fully saturate the coil's cotton. This is crucial for optimal performance and coil longevity.
Operating Instructions
The DotMod dot TANK MAX 0.15Ω coil is designed for optimal performance within a specific wattage range.
- Recommended Wattage: This 0.15Ω coil performs best between 70W and 90W.
- Initial Use: When using a new coil, start at the lower end of the recommended wattage range (e.g., 70W) and gradually increase the wattage until you find your preferred vapor production and flavor.
- Vaping Technique: Use a direct-to-lung (DTL) vaping style with this coil for the best experience.
Maintenance
- Coil Replacement: Coils are consumable parts and will need to be replaced regularly. Replace your coil when you notice a decrease in flavor, reduced vapor production, or a burnt taste. The lifespan of a coil varies depending on usage habits and e-liquid type.
- Tank Cleaning: Regularly clean your DotMod dot TANK MAX to ensure optimal performance and hygiene. Disassemble the tank and rinse all parts (except the coil) with warm water. Allow all components to dry completely before reassembly.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No vapor / Weak vapor | Coil not installed correctly, coil burnt out, low e-liquid, insufficient wattage. | Ensure coil is seated firmly. Replace coil if burnt. Refill tank. Increase wattage within recommended range. |
| Burnt taste | Coil not primed, coil burnt out, chain vaping, e-liquid too low. | Ensure coil is fully saturated before first use. Replace coil. Allow time between puffs. Refill tank. |
| Leaking | Coil not installed correctly, damaged O-rings, overfilling, incorrect e-liquid viscosity. | Reinstall coil. Check O-rings for damage. Do not overfill. Use appropriate e-liquid for sub-ohm coils. |
Specifications
| Feature | Detail |
|---|---|
| Model | dotmod-c009 |
| Resistance | 0.15Ω |
| Recommended Wattage | 70-90W |
| Compatibility | DotMod dot TANK MAX |
| Quantity per Pack | 5 pieces |
| Color | Silver |
| Manufacturer | DotMod |
| Country of Origin | China |
Warranty and Support
For warranty information and customer support, please refer to the official DotMod website or contact your authorized retailer. Keep your proof of purchase for any warranty claims.
For further assistance, you may visit the DotMod Official Website or contact their customer service directly.