Missyou 3DHologramFan Desktop Stand (15-inch Height) Instruction Manual

1. Introduction

This instruction manual provides detailed guidance for the assembly, operation, and maintenance of your Missyou 3DHologramFan Desktop Stand. This stand is designed to securely support 3D hologram fans up to 27.5 inches, offering a stable and elegant display solution. Please read this manual thoroughly before assembly and use to ensure proper installation and safe operation.

2. Safety Information

• Handle the tempered glass base with care to prevent breakage or injury.
• Ensure all screws and connections are tightened securely before placing the hologram fan on the stand.
• Keep small parts, such as screws and nuts, out of reach of children.
• Do not overload the stand. It is designed for hologram fans up to 5 kg (11 lbs).
• Place the stand on a stable, flat surface to prevent tipping.

3. Package Contents

Verify that all components listed below are present in your package:

• 2 x Aluminum Profiles (for vertical support)
• 1 x Tempered Glass Base
• 1 x Acrylic T-shaped Mounting Bracket
• 2 x Metal Connectors (Grub Bolts)
• 8 x Small Bolts (for acrylic bracket)
• 8 x Small Washers (for small bolts)
• 8 x Small Nuts (for small bolts)
• 1 x Long Bolt (for base connection)
• 1 x Long Washer (for long bolt)
• 1 x Long Nut (for long bolt)
• 2 x Allen Keys (one large, one small)
• 4 x Rubber Pads (for base bottom)
• 1 x Wire Holder (clear, self-adhesive)
• 1 x End Cap (plastic, for top of profile)

Figure 1: All components included in the package.

4. Setup

Follow these steps to assemble your desktop stand:

1. Prepare Components: Unpack all parts and remove any protective films from the tempered glass base and acrylic mounting bracket. Identify the two aluminum profiles. One profile has pre-drilled holes on its side, and the other does not.
2. Assemble Vertical Support:
   
   

   Figure 2: Internal connection mechanism of aluminum profiles.

   Insert the two metal connectors (grub bolts) into the side grooves of the aluminum profile that has no pre-drilled holes. Ensure the narrow end of the connector is facing up and the wider end is facing down. Slide the second aluminum profile (with holes) onto the connectors, aligning the grooves. Tighten the grub bolts using the provided small Allen key until the two profiles are securely joined without any gaps.
3. Attach Vertical Support to Base:
   
   

   Figure 3: Attaching the vertical support to the glass base.

   Align the bottom of the assembled aluminum profile with the central screw hole on the tempered glass base. Insert the long bolt through the bottom of the glass base, through the long washer, and into the threaded hole at the bottom of the aluminum profile. Secure it tightly with the large Allen key.
4. Attach Hologram Fan Mounting Bracket:
   
   

   Figure 4: The acrylic mounting bracket for the hologram fan.

   Place the acrylic T-shaped mounting bracket onto the top of the aluminum profile, aligning its three holes with the corresponding holes on the profile. Insert the small bolts through the acrylic bracket, then add a small washer and a small nut on the other side. Tighten all three bolts securely using the small Allen key.
5. Install the Hologram Fan:
   
   

   Figure 5: The fully assembled stand with a hologram fan in use.

   Carefully align your 3D hologram fan's mounting points with the bolts on the newly installed acrylic bracket. Secure the fan using the appropriate nuts or screws provided with your hologram fan. Ensure the fan is stable and level.
6. Cable Management: Use the self-adhesive clear wire holder to neatly secure the hologram fan's power cable along the aluminum profile, ensuring it does not interfere with the fan's operation or stability.

5. Operating

Once the Missyou 3DHologramFan Desktop Stand is fully assembled and your hologram fan is securely mounted, connect your hologram fan to its power source according to its own instruction manual. The stand itself does not require power. Ensure the fan is properly balanced on the stand for optimal display performance.

6. Maintenance

• Cleaning: Use a soft, dry cloth to wipe down the aluminum profiles and tempered glass base. For stubborn smudges on the glass, a glass cleaner can be used, applied to the cloth first, not directly to the stand.
• Avoid Harsh Chemicals: Do not use abrasive cleaners, solvents, or harsh chemicals as they may damage the finish of the aluminum or the surface of the glass.
• Check Connections: Periodically check all screws and connections to ensure they remain tight and secure. Retighten if necessary.

7. Troubleshooting

• Stand is Wobbly:
  Solution: Ensure the stand is placed on a completely flat and stable surface. Check all assembly screws, especially those connecting the aluminum profiles and the base, and tighten them firmly.
• Hologram Fan is Not Level:
  Solution: Verify that the acrylic mounting bracket is installed correctly and securely. Adjust the fan's mounting points if possible, or re-check the tightness of the screws on the acrylic bracket.
• Difficulty Assembling Aluminum Profiles:
  Solution: Ensure the metal connectors (grub bolts) are properly inserted into the grooves and are not overtightened before sliding the second profile. Loosen them slightly if needed, slide the profiles together, then tighten.

8. Specifications

Figure 6: Key dimensions of the desktop stand.

9. Warranty & Support

For any questions, issues, or warranty claims regarding your Missyou 3DHologramFan Desktop Stand, please contact Missyou customer support through the retailer's platform or the official Missyou website. Please retain your proof of purchase for warranty validation.