POOL BLASTER CX-300

Download PDFFree PDF. The Save button below keeps a bookmark and private notes in your account.

POOL BLASTER CX-300 Cordless Robotic Pool Cleaner Instruction Manual

Model: CX-300

1. Introduction

The POOL BLASTER CX-300 is an advanced cordless robotic pool cleaner designed for efficient and effortless cleaning of both smaller in-ground and above-ground pools. This manual provides essential information for the proper setup, operation, and maintenance of your device.

  • Cordless Operation: Eliminates the need for cumbersome cords and hoses, offering unrestricted movement.
  • Extended Runtime: Provides over 2 hours of thorough cleaning on a single charge.
  • Smart Navigation: Utilizes proprietary technology to customize cleaning paths for optimal results.
  • Versatile Cleaning Modes: Offers three modes: Full-Pool Cleaning, Floor Only, and Wall Only.
  • Wall Climbing Capability: Designed to scrub walls and waterlines for comprehensive cleaning.
  • Lightweight Design: Easy to handle and retrieve from the pool.

2. Setup and Initial Use

Before first use, ensure the POOL BLASTER CX-300 is fully charged. The device comes pre-assembled and ready for operation after charging.

  1. Charging: Connect the charger to the device's charging port. The indicator light will show charging status. Ensure the protective cap is tightened before placing the device in water.
  2. Power On: Press and hold the power button until the LED lights illuminate.
  3. Select Cleaning Mode: Use the mode selection button to choose your desired cleaning pattern (Full-Pool, Floor Only, or Wall Only).
  4. Submerge: Gently place the cleaner into the pool within 3 minutes of activation. It will sink and begin its cleaning cycle.
POOL BLASTER CX-300 being placed into a pool
Figure 2.1: Placing the POOL BLASTER CX-300 into the pool for its cleaning cycle.

For a visual guide on setup and operation, please refer to the video below:

Video 2.1: Official product video demonstrating the setup and operation of the POOL BLASTER CX-300 Cordless Robotic Pool Vacuum.

3. Operating the Cleaner

The CX-300 is equipped with Smart Navigation to optimize its cleaning path. It can clean the entire pool, including the floor, walls, and waterline, or focus on specific areas based on the selected mode.

POOL BLASTER CX-300 cleaning the pool floor, collecting sand and silt
Figure 3.1: The CX-300 efficiently cleans the pool floor, collecting fine debris like sand and silt.
POOL BLASTER CX-300 climbing and scrubbing a pool wall
Figure 3.2: The robotic cleaner scrubs the waterline and cleans walls and steps with ease.

The device will automatically shut off once its cleaning cycle is complete or the battery is depleted. Use the included hook attachment with a standard pool pole for easy retrieval from the water.

Man using a hook to retrieve the POOL BLASTER CX-300 from the pool
Figure 3.3: A hook is included for convenient retrieval of the lightweight robot from the pool.

4. Maintenance

Regular cleaning of the filter basket is crucial for maintaining optimal performance.

  1. Remove Filter Basket: Open the top lid of the cleaner and carefully remove the reusable debris chamber cartridge.
  2. Empty Debris: Dispose of collected debris into a trash receptacle.
  3. Rinse Filter: Use a garden hose to thoroughly rinse the filter basket. Ensure all fine particles and debris are flushed out. Rinse from the outside of the filter inwards to push debris out, rather than further into the mesh.
  4. Reinstall: Once clean, allow the filter to dry before reinserting it into the cleaner.
Hands removing and cleaning the reusable debris filter basket from the POOL BLASTER CX-300
Figure 4.1: The reusable debris chamber cartridge is easy to remove, clean, and replace.

For a demonstration of filter cleaning, refer to the video below:

Video 4.1: A detailed review including how to clean the filter basket of the POOL BLASTER CX-300.

5. Specifications

FeatureDetail
Model NameCX-300
Item Model Number72000RR
Power SourceBattery Powered (1 Lithium Ion battery included)
Battery TypeLithium-Ion
Battery Energy Content99.36 Watt Hours
Runtime2.5 Hours
Item Weight17.2 Pounds
Product Dimensions13.86"L x 9.85"W x 15.12"H
MaterialPlastic
ColorBlue
Control MethodRemote (Smart Navigation)
Installation TypeRobotic
UPC852506007713

6. Troubleshooting

If your POOL BLASTER CX-300 is not operating as expected, consider the following:

  • No Power/Short Runtime: Ensure the battery is fully charged. Refer to the charging instructions in Section 2.
  • Poor Suction/Ineffective Cleaning: Check and clean the filter basket thoroughly. A clogged filter can significantly reduce performance.
  • Movement Issues: Verify that the tracks and brushes are free from debris or obstructions. Ensure the pool surface is suitable for robotic cleaners.
  • Charger Connection: Some users have reported needing to wiggle the charger plug to find the 'sweet spot' for proper connection. Ensure the indicator light changes to red (charging) or green (charged).

7. Warranty and Support

The POOL BLASTER CX-300 comes with a 1 Year Limited Manufacturer Warranty.

For any questions, technical assistance, or warranty claims, please contact our US-based customer service team. A dedicated line is available for Water Tech's robotic pool cleaners via chat, email, and phone.

Manufacturer: Water Tech Corp

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.