1. Introduction
The Swokely Smart Fingerprint Door Lock provides advanced security and convenient access to your property. This keyless entry system integrates multiple unlocking methods, including fingerprint recognition, password, IC card, traditional key, and mobile application control. Designed for durability and ease of use, it is suitable for doors with a thickness of 30-60mm.
2. Safety Information
- Read all instructions carefully before installation and use.
- Do not expose the lock to direct water spray or corrosive liquids.
- Ensure correct battery polarity when inserting batteries.
- Keep emergency keys in a secure location outside the property.
- Avoid using abrasive cleaners on the lock's surface.
- This device is intended for indoor use or protected outdoor environments.
3. Package Contents
Verify that all components are present before beginning installation:
- 1 x Front Panel
- 1 x Rear Panel
- 2 x Anti-slip Rubber Pad
- 1 x Screw Pack
- 2 x Emergency Key
- 2 x Induction Card (IC Card)
- 1 x Guide Card
- 1 x Locking Tongue
- 1 x Instruction Manual (this document)
4. Specifications
| Fingerprint Capacity | 100 pieces |
| Recognition Speed | 0.5 seconds |
| Material | Aluminum alloy |
| Password Digits | 6-10 digits |
| Lock Cylinder Level | C-level safety lock cylinder |
| Working Temperature | -20 ℃ to 60 ℃ (-4 ℉ to 140 ℉) |
| Fingerprint Head | Biological fingerprint head |
| Power Supply | 4 x AA batteries (not included) |
| Suitable Door Thickness | 30-60mm |
| Unlock Methods | Fingerprint, Password, IC Card, Key, Access Lock APP, Combination Unlock |
| Product Dimensions | 18.6 x 6.6 x 5.9 cm (7.3 x 2.6 x 2.3 inches) |
Image: Detailed dimensions of the Swokely Smart Fingerprint Door Lock, showing height (186mm), width (66mm), and depth (59mm).
5. Installation Guide
This section provides general steps for installing the Swokely Smart Fingerprint Door Lock. For detailed instructions, refer to the included guide card and diagrams.
Image: The Swokely Smart Fingerprint Door Lock installed on a wooden door, illustrating its appearance after installation.
- Prepare the Door: Ensure your door thickness is between 30-60mm. Remove any existing lock hardware.
- Install the Locking Tongue: Insert the locking tongue into the door edge and secure it with screws. Ensure the latch operates smoothly.
- Install the Front Panel: Route the cable from the front panel through the door hole. Position the front panel on the exterior side of the door.
- Install the Rear Panel: Connect the cable from the front panel to the rear panel. Align the rear panel with the front panel and secure it using the provided screws. Ensure the anti-slip rubber pads are correctly placed between the lock and the door surface.
- Insert Batteries: Open the battery compartment on the rear panel and insert four AA batteries, observing correct polarity. Close the compartment.
- Test Operation: After installation, test the mechanical key and the handle operation to ensure the lock functions correctly before proceeding with electronic setup.
6. Setup and Configuration
6.1 Initial Setup
- Upon first power-up, the lock will be in factory default mode.
- It is recommended to set an administrator fingerprint or password immediately.
6.2 Mobile Application Pairing
The lock supports control via a mobile application. Download the designated "Access Lock APP" from your device's app store.
- Download and install the "Access Lock APP".
- Create an account and log in.
- Follow the in-app instructions to add your new smart lock. This typically involves activating a pairing mode on the lock and confirming within the app.
6.3 User Management (Fingerprint, Password, IC Card)
The lock allows registration of up to 100 fingerprints and multiple passwords and IC cards.
Image: Visual representation of the five primary unlocking methods: fingerprint, password, mobile application, physical key, and IC card.
- Registering Fingerprints:
- Access the fingerprint registration menu (usually via the app or by entering a master code on the keypad).
- Place your finger on the sensor multiple times from different angles until registration is complete.
- Setting Passwords:
- Enter the password setting menu.
- Input your desired 6-10 digit password, then confirm.
- Consider using the anti-peep virtual password feature by entering random digits before and after your actual password.
- Registering IC Cards:
- Enter the IC card registration menu.
- Present the IC card to the designated sensor area on the lock until it is successfully registered.
7. Operating Instructions
7.1 Unlocking Methods
- Fingerprint Unlock: Place your registered finger on the fingerprint sensor. The lock will unlock if the fingerprint is recognized.
- Password Unlock: Enter your registered password on the keypad, followed by the '#' key. The lock will unlock.
- IC Card Unlock: Present a registered IC card to the card reader area on the lock. The lock will unlock.
- Key Unlock: Insert the emergency key into the keyhole and turn to unlock the door manually.
- APP Unlock: Open the "Access Lock APP" on your smartphone and follow the prompts to remotely unlock the door.
Image: The Swokely Smart Fingerprint Door Lock, showing both the exterior panel with fingerprint sensor and keypad, and the interior panel.
7.2 Locking the Door
The lock typically auto-locks after a few seconds once the door is closed. You can also manually lock it from the inside using the anti-theft button or handle, or via the mobile application.
8. Maintenance
- Battery Replacement: When the low battery warning is issued, replace all four AA batteries promptly. Use high-quality alkaline batteries for optimal performance.
- Emergency Power: If batteries completely drain, use the emergency keys or connect a power bank to the emergency power port (usually Micro USB) to temporarily power the lock.
- Cleaning: Wipe the lock's surface with a soft, dry cloth. Do not use harsh chemicals, abrasive cleaners, or excessive moisture.
- Fingerprint Sensor: Keep the fingerprint sensor clean and dry for accurate recognition.
9. Troubleshooting
| Problem | Solution |
|---|---|
| Lock does not respond. | Check battery level. Replace batteries if low. Use emergency power or key. |
| Fingerprint not recognized. | Ensure finger is clean and dry. Try different angles. Re-register fingerprint if issue persists. |
| Password not accepted. | Verify correct password entry. Ensure no virtual digits are accidentally included if not intended. Reset password if forgotten. |
| Lock does not pair with APP. | Ensure Bluetooth is enabled on your phone. Restart the app and the lock. Check app permissions. |
| Low battery warning. | Replace all four AA batteries immediately. |
10. Warranty and Support
This Swokely Smart Fingerprint Door Lock is covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms, duration, and to obtain technical support, please refer to the warranty card included with your product or contact Swokely customer service through their official website or the contact information provided in your purchase documentation.
When contacting support, please have your product model number (PTW8074579649513RC) and purchase date readily available.
