Metalux WP 2 ft. Integrated LED Wraparound Light

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Metalux WP 2 ft. Integrated LED Wraparound Light, Model 2WP1540R. This energy-efficient LED fixture is designed for various commercial and residential applications, offering 1800 lumens of 4000K cool white light. Its compact, low-profile design and prismatic lens ensure uniform, glare-free illumination. Please read this manual thoroughly before installation and use to ensure safe and proper operation.

Figure 1: Metalux WP 2 ft. Integrated LED Wraparound Light. This image displays the complete LED wraparound light fixture, featuring a white housing and a textured, prismatic lens designed for even light distribution.

2. Safety Information

WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installation or servicing.

• All wiring connections must be in accordance with local and National Electrical Code (NEC) standards. If you are unfamiliar with proper electrical wiring connections, consult a qualified electrician.
• Ensure the fixture is properly grounded to avoid potential electrical hazards.
• Do not install this fixture with wet hands or while standing on a wet or damp surface.
• This fixture is suitable for damp locations. Do not expose to direct water spray or submersion.
• Do not attempt to modify or disassemble the fixture. There are no user-serviceable parts inside.
• Verify that the supply voltage is 120V before connecting the fixture.

3. Package Contents

Verify that all components are present and undamaged before proceeding with installation.

• Metalux WP 2 ft. Integrated LED Wraparound Light Fixture (Model 2WP1540R)
• Installation Hardware (e.g., mounting screws, wire nuts) - May vary by package.

4. Specifications

5. Installation Instructions (Setup)

Before You Begin:

• Turn off power at the circuit breaker or fuse box.
• Ensure you have the necessary tools: screwdriver, wire strippers, drill, measuring tape, safety glasses.
• Review local electrical codes for compliance.

Mounting Options:

The fixture can be surface mounted directly to a standard junction box, or suspended via chain or pendant (hardware not included for suspension). The fixture features pre-drilled holes and knockouts for flexible installation.

Figure 2: Technical Drawing with Dimensions. This diagram illustrates the top and side views of the Metalux WP LED light, detailing its dimensions (24" L x 5" W x 2-7/16" H), J-Box access point, ground screw location, and four ceiling stand-off embossments for mounting.

Step-by-Step Installation:

1. Prepare the Fixture: Remove the lens and any packaging materials from the fixture.
2. Position the Fixture: Hold the fixture against the mounting surface (ceiling or wall) at the desired location. Mark the positions for mounting screws, aligning with the fixture's mounting holes or embossments. If mounting to a junction box, align the J-Box access with the box.
3. Secure the Fixture:
   • For surface mounting: Drill pilot holes if necessary and secure the fixture directly to the surface using appropriate mounting screws (not always included). Ensure the fixture is firmly attached.
   • For junction box mounting: Feed the supply wires through the J-Box access hole. Secure the fixture to the junction box using screws provided with the junction box or appropriate mounting hardware.
   • For chain/pendant mounting: Attach appropriate hanging hardware (not included) to the fixture's designated points and suspend from the ceiling structure.
4. Wire Connections:
   • Connect the black wire from the fixture to the black (hot) wire from the supply using a wire nut.
   • Connect the white wire from the fixture to the white (neutral) wire from the supply using a wire nut.
   • Connect the green or bare copper (ground) wire from the fixture to the green or bare copper (ground) wire from the supply using a wire nut. Ensure the ground screw on the fixture is also connected to the building's ground system.

   Ensure all connections are secure and no bare wire is exposed.

5. Reattach Lens: Carefully reattach the prismatic lens to the fixture, ensuring it is securely seated.
6. Restore Power: Turn on power at the circuit breaker or fuse box. Test the light fixture.

6. Operating Instructions

The Metalux WP 2 ft. Integrated LED Wraparound Light operates as a standard on/off fixture. Once properly installed and powered, it will illuminate when the connected wall switch or power source is activated.

• Power On/Off: Use the wall switch connected to the fixture to turn the light on or off.
• Non-Dimming: This fixture is equipped with a non-dimming driver and is not compatible with dimmer switches. Attempting to use a dimmer may damage the fixture or cause erratic operation.

7. Maintenance

The Metalux WP LED Wraparound Light is designed for long-term, low-maintenance operation. The integrated LED light source has a rated life of 50,000 hours (L70), meaning no bulb replacement is necessary.

• Cleaning: To clean the fixture, ensure power is turned off at the circuit breaker. Use a soft, dry, or slightly damp cloth to wipe the exterior surfaces. Do not use abrasive cleaners, solvents, or cleaners containing alcohol, as these can damage the finish or lens.
• Inspection: Periodically inspect the fixture for any signs of damage or loose connections. If any issues are found, disconnect power and consult a qualified electrician.

8. Troubleshooting

If you experience issues with your Metalux WP LED Wraparound Light, refer to the following common troubleshooting steps:

If the problem persists after attempting these solutions, contact customer support or a qualified electrician.

9. Warranty and Support

Warranty: This Metalux WP LED Wraparound Light is covered by a 5-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, accident, misuse, abuse, or unauthorized modifications.

Customer Support: For technical assistance, warranty claims, or further information, please contact Metalux customer support. Refer to the product packaging or the manufacturer's website for current contact details.

Please have your model number (2WP1540R) and proof of purchase available when contacting support.