Instruction Manual

Introduction

This manual provides detailed instructions for the installation, maintenance, and general use of your new SPEDWHEL Original Pedal Sticker for the Teverun Blade Mini Pro Electric Scooter. This anti-slip silicone sticker is designed as a direct replacement accessory to enhance the grip and appearance of your scooter's pedal board.

Please read this manual thoroughly before proceeding with installation to ensure proper application and longevity of the product.

Safety Information

• Ensure the scooter is powered off and stable before beginning any installation or maintenance.
• Keep the sticker and any tools out of reach of children.
• Handle the sticker carefully to avoid damaging the adhesive backing.
• Dispose of old stickers and packaging responsibly.

Setup and Installation

Follow these steps carefully to install your new pedal sticker:

1. Prepare the Surface: Thoroughly clean the surface of the scooter's pedal board where the sticker will be applied. Use a degreaser or rubbing alcohol to remove any dirt, grease, or residue. Ensure the surface is completely dry before proceeding.
2. Remove Old Sticker (if applicable): If replacing an existing sticker, carefully peel off the old one. Clean any remaining adhesive residue from the pedal board.
3. Align the Sticker: Carefully position the new pedal sticker on the scooter's pedal board without removing the adhesive backing. Ensure it aligns correctly with the edges and any cutouts for screws or other features. This step is crucial for a neat finish.
4. Apply the Sticker:
   

   Image: The pedal sticker laid flat, showcasing its design and precise cutouts for the Teverun Blade Mini Pro scooter.
   

   Image: The flexible silicone material of the sticker, demonstrating how it can conform to the scooter's surface. The white backing protects the adhesive layer.

   Once aligned, peel off a small section of the adhesive backing from one end of the sticker. Carefully press this section onto the pedal board, working your way across the sticker. Gradually peel off the rest of the backing while smoothing the sticker down with your hand or a soft cloth to prevent air bubbles. Apply firm, even pressure across the entire surface.

5. Cure Time: Allow the adhesive to set for at least 24 hours before riding the scooter. This ensures maximum adhesion and prevents the sticker from peeling prematurely.

Note: This pedal sticker is designed for single use. Once applied and removed, its adhesive properties may be compromised.

Operating Considerations

While the sticker itself does not alter the scooter's operation, proper adhesion is key to its function. Ensure the sticker is fully adhered before use to provide optimal anti-slip performance.

Image: A detailed view of the textured surface, highlighting the anti-slip properties designed to enhance rider grip.

The textured surface is designed to provide enhanced grip for your feet during rides, contributing to a safer and more stable experience.

Maintenance

To maintain the appearance and anti-slip properties of your pedal sticker:

• Cleaning: Wipe the sticker surface with a damp cloth to remove dirt and debris. For stubborn stains, a mild soap solution can be used. Avoid harsh chemicals or abrasive cleaners, as these can damage the silicone material or the printed design.
• Inspection: Periodically inspect the edges of the sticker for any signs of peeling. If minor peeling occurs, you may be able to press it back down firmly. For significant peeling or damage, replacement is recommended.

Troubleshooting

Sticker Not Adhering Properly

• Issue: The sticker is not sticking or is peeling shortly after application.
• Solution:
  • Ensure the pedal board surface was thoroughly cleaned and completely dry before application. Any dust, oil, or moisture will prevent proper adhesion.
  • Apply firm, even pressure across the entire sticker surface during installation, especially along the edges.
  • Allow the recommended cure time (at least 24 hours) before using the scooter.
  • If the issue persists, the surface may require a more aggressive cleaning or the sticker may need to be replaced if its adhesive is compromised.

Air Bubbles Under the Sticker

• Issue: Air bubbles are visible under the sticker after application.
• Solution:
  • During application, use a soft cloth or squeegee to smooth out the sticker from the center outwards, pushing any air bubbles towards the edges.
  • For small, trapped bubbles, you can try gently pressing them towards the nearest edge. Avoid puncturing the sticker.

Specifications

Warranty and Support

For any questions regarding the installation, performance, or replacement of your SPEDWHEL pedal sticker, please contact SPEDWHEL customer support. Refer to your purchase documentation for specific warranty terms and contact information.

You can typically find support contact details on the product packaging or the retailer's website where the product was purchased.