Introduction
The Waveform Window Entry Cable provides a convenient and non-invasive solution for routing coaxial cables from outdoor antennas or devices to indoor equipment. Its ultra-flat ribbon design allows cables to pass through closed windows and doors without the need for drilling, preserving the integrity of your property. This manual outlines the product features, installation procedures, and specifications to ensure optimal performance.
Product Overview
The Waveform Window Entry Cable is designed for low-loss signal transmission, featuring SMA Male to SMA Female connectors. The core of the cable is an ultra-thin, flexible ribbon that can be compressed within a window or door frame. It includes indoor and outdoor connection boxes with adjustable cable exits for tidy cable management.
What's Included:
- Waveform Window Entry Cable (Twin [v1] variant)
- Mounting Screws
Figure 1: Waveform Window Entry Cable (Twin and Quad versions shown, Twin version installed).
Unboxing and Overview Video:
Video 1: An official overview of the Waveform Window Entry Cable, demonstrating its components and features.
Setup and Installation
The Window Entry Cable is designed for simple and straightforward installation, compatible with various window and door types.
1. Prepare the Cable:
- Identify the outdoor end (SMA Female connectors) and the indoor end (SMA Male pigtail connectors).
- Ensure the flat ribbon section is free from kinks or damage.
2. Position the Cable:
- Open your window or door.
- Place the flat ribbon section of the cable across the window or door frame.
- For horizontally sliding windows, position the ribbon on the side frame where the window closes against it, rather than over the sliding rail, to prevent damage.
- Gently close the window or door, ensuring the ribbon is compressed evenly and the window/door seals completely.
Figure 2: Proper placement of the Window Entry Cable in a window frame.
3. Mount the Connection Boxes:
The indoor and outdoor connection boxes can be mounted using either the pre-installed adhesive tape or the included screws.
- Adhesive Mounting: Peel off the backing from the adhesive tape on the back of each box and firmly press the boxes onto a clean, dry surface adjacent to the window/door frame.
- Screw Mounting: Open the connection boxes to reveal the screw holes. Use the provided screws to secure the boxes to the wall or frame. Close the boxes securely after mounting to ensure weatherproofing.
4. Adjust Cable Exits (Optional):
The cable exits on both the indoor and outdoor boxes are adjustable to optimize cable routing and create drip loops for outdoor installations.
- Gently open the cover of the connection box.
- Reposition the internal cable guide to direct the cables in the desired direction (e.g., downwards for drip loops).
- Close the cover firmly to secure the cable guide and maintain weather resistance.
Figure 3: Adjustable cable exits for optimized cable management.
5. Connect Your Devices:
- Connect your outdoor antenna's SMA Male cables to the SMA Female connectors on the outdoor box.
- Connect the SMA Male pigtail cables from the indoor box to your cellular router, gateway, hotspot, or other compatible device.
Figure 4: Compatibility with various cellular devices and Waveform antennas.
Operation
Once installed, the Waveform Window Entry Cable functions as a transparent conduit for your coaxial signals. It is designed to maintain signal integrity with minimal insertion loss across a wide frequency range, ensuring reliable performance for your connected devices.
Compatibility:
The cable is universally compatible with most window types, including sliding, awning, hung, casement, and hopper windows, as well as many doors. Its SMA connectors ensure broad compatibility with a variety of cellular routers, gateways, hotspots, and external antennas, including Waveform's QuadPro and QuadMini antennas.
Figure 5: Universal compatibility with various window types.
Maintenance
The Waveform Window Entry Cable requires minimal maintenance. Periodically inspect the cable and connectors for any signs of wear, damage, or corrosion, especially on the outdoor side. The cable is UV resistant, but extreme weather conditions over prolonged periods may affect its lifespan. Ensure all connections remain tight and secure for optimal signal performance.
Troubleshooting
- No Signal or Poor Signal:
- Ensure all SMA connectors are securely tightened.
- Verify that the window or door is fully closed and compressing the flat ribbon evenly.
- Check for any visible damage to the flat ribbon or connectors.
- Confirm that the outdoor antenna is correctly aimed and functioning.
- Window/Door Not Closing Properly:
- Ensure the flat ribbon is positioned correctly and not obstructed by debris.
- Verify that the ribbon is not twisted or folded, which could prevent a proper seal.
- Cable Damage:
- Handle the interior pigtail leads with care during installation and connection, as they can be delicate.
- Avoid excessive bending or pulling on the cables, especially near the connection points.
Specifications
Figure 6: Detailed product specifications.
| Feature | Specification |
|---|---|
| Brand | Waveform |
| Model | 113-WP-SFM-2 |
| Connector Type | SMA |
| Cable Type | Low-loss RG1.13 |
| Compatible Devices | Coaxial Cable, Cellular Routers, Gateways, Hotspots |
| Special Feature | UV Resistant |
| Connector Gender | SMA-Male to SMA-Female |
| Number of Pins | 2 |
| Indoor Outdoor Usage | Indoor, Outdoor |
| Item Shape | Flat |
| Impedance | 50 Ω |
| VSWR | ≤ 2.0 |
| Insertion Loss (600 MHz) | 0.84 dB |
| Insertion Loss (2.5 GHz) | 1.5 dB |
| Insertion Loss (5 GHz) | 2.5 dB |
| Ribbon Thickness | 2.3 mm (0.09 in) |
| Ribbon Length | 130 mm (5.1 in) |
| Total Length | 60 cm (2 ft) |
Warranty and Support
For warranty information, technical support, or any questions regarding your Waveform Window Entry Cable, please contact Waveform customer service.
Email: help@waveform.com
Phone: +1-800-761-3041
You can also visit the official Waveform website for additional resources and product information.
