Jebao DEP Bluetooth Submersible Vario DC Pump DEP-10000 User Manual

1. Introduction

1.1 Product Overview

The Jebao DEP Bluetooth Submersible Vario DC Pump is an energy-efficient pump designed for both saltwater and freshwater aquarium systems. It utilizes advanced frequency conversion electronic technology, resulting in up to 65% energy savings and ultra-quiet operation. The pump features a Bluetooth connection for APP control, an LED screen display for manual adjustments, and a feeding suspension function.

1.2 Key Features

• Bluetooth connection for APP control.
• Manual and APP control system with visual LCD display.
• Bottom-suction water intake for low water-level operation.
• Sine wave technology for ultra-quiet operation.
• IC electronic detection for dry/locked rotor protection.
• Feeding suspension function for 10 minutes with delayed restart.

2. Package Contents

Carefully unpack all components and verify that all items listed below are present and undamaged. If any items are missing or damaged, contact your retailer.

Figure 2.1: All components included with the Jebao DEP-10000 pump, including the pump unit, controller, power adapter, and various hose adapters.

• Jebao DEP-10000 DC Pump Unit
• Controller with LED screen display
• Power Adapter (110 Volts)
• Various Outlet Hose Adapters (3/4", 1", 1-1/4", 1-1/2")
• Pipe Fittings (3/4", 1", 1-1/4")
• User Manual

3. Important Safety Instructions

Read and follow all safety instructions before installing and operating this pump. Failure to do so may result in injury or damage to the product.

• Electrical Safety: Always disconnect power to all aquarium equipment before performing any maintenance or installation. Ensure the power outlet has a ground fault circuit interrupter (GFCI). Do not operate the pump if the power cord or plug is damaged.
• Water Immersion: This pump is designed for submersible use only. Do not operate it dry.
• Voltage: Ensure the power supply voltage matches the pump's requirements (110 Volts).
• Placement: Position the pump securely to prevent movement during operation.
• Children: Keep this product out of reach of children.
• Temperature: Do not use the pump with liquids exceeding 35°C (95°F).

4. Setup and Installation

4.1 Component Identification

Familiarize yourself with the pump unit and its various parts before installation.

Figure 4.1: Side view of the Jebao DEP-10000 pump, highlighting the main body and intake screen.

4.2 Placement

1. The DEP-10000 pump is designed for submersible operation. Place the pump entirely underwater in your aquarium or sump.
2. Ensure the pump is placed on a stable, flat surface to minimize vibration and noise.
3. Verify that the water intake is clear of obstructions to allow for optimal flow.

4.3 Connecting Hoses and Adapters

1. Select the appropriate hose adapter (3/4", 1", 1-1/4", or 1-1/2") and pipe fitting (3/4", 1", or 1-1/4") for your plumbing system.
2. Attach the chosen adapter securely to the pump's outlet.
3. Connect your return line hose or PVC piping to the adapter. Ensure all connections are tight to prevent leaks.

Figure 4.2: Top view of the Jebao DEP-10000 pump, illustrating the threaded outlet for hose connection.

4.4 Power Connection

1. Connect the pump's power cable to the controller.
2. Connect the power adapter to the controller.
3. Plug the power adapter into a GFCI-protected electrical outlet.

Figure 4.3: Angled view of the Jebao DEP-10000 pump, showing the power cable connecting to the controller.

5. Operating the Pump

5.1 Initial Start-up

Once the pump is installed and connected to power, it will automatically start. The LED display on the controller will show the current operating status and flow rate.

5.2 Manual Control

The controller features an LED screen and buttons for direct adjustment of the pump's flow rate. Refer to the controller's specific button functions for increasing or decreasing flow.

5.3 Bluetooth APP Control

The pump can be controlled wirelessly via a dedicated mobile application.

1. Download the App: Search for the official Jebao/Jecod app on your smartphone's app store.
2. Enable Bluetooth: Ensure Bluetooth is enabled on your smartphone.
3. Connect to Pump: Open the app and follow the on-screen instructions to discover and pair with your DEP-10000 pump. Note that the app typically requires a 2.4GHz Wi-Fi connection for initial setup or certain functionalities.
4. Adjust Settings: Use the app interface to precisely control the pump's flow rate, set schedules, and activate special functions.

5.4 Feeding Suspension Function

The pump includes a feeding mode to temporarily stop water flow during feeding times. Activate this function via the controller or the mobile app. The pump will suspend operation for 10 minutes and then automatically restart.

6. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your pump.

6.1 Regular Cleaning

1. Disconnect Power: Always unplug the pump from the power outlet before cleaning.
2. Remove from Water: Carefully remove the pump from your aquarium or sump.
3. Disassemble: Disassemble the pump housing and impeller cover.
4. Clean Components: Use a soft brush and clean water to remove any algae, debris, or calcium buildup from the impeller, impeller shaft, and pump housing. For stubborn deposits, a mild vinegar solution can be used, followed by thorough rinsing.
5. Reassemble: Reassemble all components, ensuring they are correctly seated.

6.2 Impeller Inspection

Periodically inspect the impeller for any signs of wear, cracks, or damage. A worn impeller can lead to reduced flow or increased noise. Replace the impeller if necessary.

7. Troubleshooting

This section addresses common issues you might encounter with your DEP-10000 pump.

8. Technical Specifications

9. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Jebao customer service directly. Keep your proof of purchase for warranty claims.