Nilight Running Boards Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Nilight Running Boards, model JL-97B. These running boards are designed specifically for 2018-2024 Jeep Wrangler JL 2 Door vehicles. Please read this manual thoroughly before beginning installation to ensure proper fitment and safe operation.

Important Note: These running boards are not compatible with Jeep Wrangler JK models or JL 4 Door models. Please verify your vehicle's model and door configuration before proceeding.

Image: Fitment type illustration showing a Jeep Wrangler JL 2 Door (highlighted in green) and a Jeep Wrangler JL 4 Door (marked with an X), indicating compatibility.

What's Included

Verify that all components listed below are present in your package before starting the installation process.

• 2 x Running Boards (Driver & Passenger Side)
• All necessary mounting hardware (brackets, bolts, washers, nuts)
• 1 x Instruction Manual (this document)

Image: Detailed view of the two running boards and a complete set of mounting hardware, including brackets, bolts, washers, and nuts, with quantities indicated.

Specifications

Image: Cross-section diagram illustrating the multi-layer construction of the running board, highlighting the durable ABS, electro-galvanized, and powder-coated layers for enhanced durability and rust resistance.

Installation Instructions

Follow these steps carefully for a successful and secure installation. It is recommended to have a second person assist with the installation.

1. Prepare Vehicle: Park your vehicle on a level surface and engage the parking brake. Ensure the area around the vehicle is clear.
2. Identify Mounting Points: Locate the factory mounting points along the rocker panel of your Jeep Wrangler JL 2 Door. These are typically pre-drilled holes in the vehicle's frame.
3. Attach Brackets: Secure the mounting brackets to the vehicle's frame using the provided bolts, washers, and nuts. Do not fully tighten the hardware at this stage; allow for some adjustment. Ensure the brackets are oriented correctly for the driver and passenger sides.
4. Position Running Boards: Carefully lift one running board and align it with the attached mounting brackets. The running board is designed to fit snugly against the vehicle's body.
5. Secure Running Boards: Attach the running board to the brackets using the remaining hardware. Again, do not fully tighten yet.
6. Adjust and Align: Once both running boards are loosely attached, adjust their position to ensure they are level and properly aligned with the vehicle's body.
7. Final Tightening: Systematically tighten all bolts and nuts, starting from the center and working outwards. Ensure all connections are secure. Do not overtighten.
8. Repeat for Other Side: Follow the same steps for the opposite side of the vehicle.

Image: A red Jeep Wrangler JL 2 Door with the Nilight running board successfully installed, showcasing its integration with the vehicle's exterior.

Operation and Safety

The Nilight Running Boards provide a convenient step for easier entry and exit from your vehicle. They also offer additional protection against road debris and minor impacts.

• Anti-Slip Surface: The textured surface of the running boards is designed to prevent slips, especially in wet or muddy conditions. Always step firmly and maintain balance.
• Load Capacity: Do not exceed the maximum load bearing capacity of 450 lbs per side. Overloading can cause damage to the running boards or the vehicle's mounting points.
• Impact Resistance: While designed to be impact-resistant, these running boards are not intended for severe off-road impacts. Avoid using them as rock sliders in extreme conditions.

Image: Magnified view of the hexagonal textured pattern on the running board surface, designed to provide enhanced grip and prevent slipping.

Image: Before and after comparison showing the running board protecting the vehicle's rocker panel from a large rock, demonstrating its impact-resistant design.

Image: A visual representation of the running board's 450 lbs load bearing capacity, depicted by a bear standing on the vehicle's hood.

Maintenance

Regular maintenance will ensure the longevity and appearance of your Nilight Running Boards.

• Cleaning: Clean the running boards regularly with mild soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
• Inspect Hardware: Periodically check all mounting hardware (bolts, nuts, brackets) for tightness. Vibrations from driving can sometimes loosen connections over time. Retighten as necessary.
• Check for Damage: Inspect the running boards for any signs of damage, such as cracks, dents, or excessive wear, especially after off-road use. Address any damage promptly to prevent further issues.

Troubleshooting

Warranty and Support

Nilight products are designed for durability and performance. For warranty information or technical support, please refer to the official Nilight website or contact their customer service directly. Keep your purchase receipt as proof of purchase.

Official Nilight Website: www.nilight.com