Mr.Go LED Cube Light Bundle User Manual

Introduction

This user manual provides essential information for the safe and effective operation of your Mr.Go 6-inch and 4-inch LED Cube Light Bundle. Please read this manual thoroughly before use and retain it for future reference.

The Mr.Go LED Cube Lights are versatile, dimmable, rechargeable, and waterproof lighting solutions featuring 16 RGB colors and 4 dynamic modes, controlled via an included remote. They are designed for various indoor and outdoor ambient lighting and decorative purposes.

Package Contents

• 1 x Mr.Go 6-inch LED Cube Light
• 1 x Mr.Go 4-inch LED Cube Light
• 1 x Remote Control
• 1 x Charging Cord
• 1 x Charger (5V 1A output)
• 1 x User Manual (this document)

Image: The Mr.Go 6-inch and 4-inch LED Cube Lights are shown alongside their remote control, illustrating the complete bundle.

Safety Information

• Do not submerge the lights in water for extended periods, despite being waterproof.
• Use only the provided charger and charging cord.
• Keep out of reach of small children.
• Avoid extreme temperatures.
• Do not attempt to disassemble or repair the unit yourself. Contact customer support if issues arise.

Setup

Initial Charging

1. Locate the charging port on the underside of each LED cube light. The charging port is protected by a rubber seal.
2. Carefully open the rubber seal to expose the charging port.
3. Connect the charging cord to the cube light and the charger to a standard wall outlet.
4. The charging status indicator light on the charger will be red during charging and turn green when fully charged.
5. A full charge takes approximately 1.5 hours.
6. Once charging is complete, disconnect the charger and ensure the rubber seal is securely closed to maintain waterproofing.

Image: A close-up view of the underside of the LED cube light, highlighting the PE cube shell, rubber seal, charging port, and the On/Off & Mode button.

Image: The charging cord and 5V 1A charger are displayed, indicating their use for recharging the cube lights.

Remote Control Preparation

• Before first use, remove the clear plastic battery insulator tab from the remote control.
• The remote control has a working range of 16 to 26 feet.
• A single remote can control multiple Mr.Go LED cube lights.

Image: A detailed diagram of the remote control, labeling buttons for Power ON/OFF, Static Brightness, Dynamic Speed, 16 Preset Colors, and Dynamic Modes (Flash, Strobe, Fade, Smooth).

Operating Instructions

Turning On/Off

• Using the Remote Control: Press the ON button to turn the light on, and the OFF button to turn it off.
• Using the Button on the Light: Short press the On/Off & Mode button on the underside of the light to turn it on and cycle through 16 colors and 4 modes. Long press the button to turn the light off.

Color Selection

• The remote control features 16 preset color buttons. Press any color button to select the desired static color.
• The light will immediately change to the selected color.

Image: Multiple Mr.Go LED cube lights are shown illuminated in a variety of RGB colors, demonstrating the 16 available color options.

Brightness Adjustment

• Use the + and - buttons under "Static Brightness" on the remote control to increase or decrease the brightness of the selected static color.

Image: A Mr.Go LED cube light is shown glowing softly in a dimly lit room, demonstrating its use as a night light or ambient lamp.

Image: A Mr.Go LED cube light is shown emitting a bright white light on a table, illustrating its full brightness capability.

Dynamic Modes

The remote control offers four dynamic lighting modes:

• FLASH: Light jumps through RGB colors.
• STROBE: Light strobes in white color.
• FADE: Light fades in and out through RGB colors.
• SMOOTH: Light gradually cycles through RGB colors.

Use the + and - buttons under "Dynamic Speed" to adjust the speed of the selected dynamic mode.

Maintenance

Cleaning

• Wipe the surface of the LED cube lights with a soft, damp cloth.
• Do not use abrasive cleaners or solvents.
• Ensure the charging port's rubber seal is closed before cleaning with water.

Storage

• Store the lights in a cool, dry place when not in use.
• If storing for an extended period, ensure the lights are fully charged before storage and recharge them every 3-6 months to maintain battery health.

Troubleshooting

Specifications

• Product Name: Mr.Go 6-inch and 4-inch LED Cube Light Bundle
• Model: B0CTWR2J2G
• Light Source: LED
• Colors: 16 RGB Colors
• Modes: Flash, Strobe, Fade, Smooth
• Material: PE Plastic (Milky white matte surface)
• Power Source: Rechargeable Battery (Battery Powered)
• Charger Output: 5V 1A
• Charging Time: Approximately 1.5 hours
• Special Features: Dimmable, Rechargeable, Waterproof (IP65 rating implied by description)
• Control Method: Remote Control (IR) and On-light button
• Remote Control Range: 16-26 feet
• Indoor/Outdoor Usage: Indoor

Warranty and Support

For warranty information or technical support, please contact Mr.Go customer service through the retailer's platform or visit the official Mr.Go store online. Please have your product model number (B0CTWR2J2G) and purchase date available when contacting support.

Mr.Go Store: Visit the Mr.Go Store on Amazon