DEWALT 12V/20V MAX XR Line Laser Instruction Manual

1. Introduction

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your DEWALT 12V/20V MAX XR Line Laser. Please read this manual thoroughly before using the product.

The DEWALT 12V/20V MAX XR High Precision 3 X 360 Line Laser is designed for challenging layout applications, offering extraordinary precision and impressive accuracy at long distances. It features dual-voltage compatibility, a fine adjust knob for micro-tuning, and comes as a complete kit including a 20V MAX battery, charger, ceiling mount bracket, and detector.

2. Important Safety Instructions

Always follow basic safety precautions when using this product to reduce the risk of injury or damage.

• Laser Safety: This is a Laser Class 2 product (<=1.5mW @ 510-530nm). Do not stare directly into the laser beam. Do not intentionally direct the laser beam at others.
• Eye Protection: Always wear appropriate eye protection when operating laser equipment.
• Battery Safety: Use only specified DEWALT 12V MAX* or 20V MAX* batteries and chargers. Do not expose batteries to water or extreme temperatures.
• Work Area: Ensure the work area is clear of obstructions and potential hazards.
• Maintenance: Refer to the Maintenance section for proper care and cleaning.

3. Product Components

The DEWALT 12V/20V MAX XR Line Laser kit includes the following components:

• DEWALT 12V/20V MAX XR Line Laser (DCLE34033D1)
• 20V MAX 2.0Ah Battery (DCB203)
• Battery Charger (DCB107)
• Ceiling Mount Bracket
• Laser Detector (DW0892G)
• Target Card
• 9V Battery (for detector)
• Hard Case

Figure 3.1: Main view of the DEWALT 12V/20V MAX XR Line Laser with its magnetic pivoting base.

Figure 3.2: Side view of the laser unit, showing the battery compartment and control panel.

4. Setup and Initial Operation

4.1 Charging the Battery

1. Connect the DCB107 Charger to a power outlet.
2. Slide the DCB203 20V MAX battery into the charger until it clicks into place.
3. Allow the battery to fully charge. Refer to the charger's indicator lights for charging status.

4.2 Installing the Battery

• Ensure the laser unit is turned off.
• Align the charged battery with the battery slot on the laser's base.
• Slide the battery into the slot until it locks securely.

Figure 4.1: The laser supports both 12V MAX* and 20V MAX* DEWALT batteries for versatile power options.

4.3 Mounting Options

The laser offers versatile attachment options for various job site needs:

• Integrated Magnetic Pivoting Base: Features rear-mounted magnets for flush attachment to metal surfaces like steel studs or metal poles.
• Tripod Mount: Equipped with 1/4 in. -20 in. and 5/8 in. - 11 in. thread tripod mounts for use with standard tripods.
• Ceiling Mount Bracket: Use the included bracket for ceiling applications.

Figure 4.2: The magnetic pivoting base allows for easy attachment to metal surfaces, while tripod mounts offer additional flexibility.

5. Operating Instructions

5.1 Powering On/Off and Self-Leveling

1. Place the laser on a stable surface or mount it securely.
2. Slide the power switch to the "ON" position. The laser will automatically begin self-leveling.
3. Wait for the laser lines to stabilize. If the unit is outside its self-leveling range, the laser lines will blink rapidly. Adjust the unit's position until the lines become solid.
4. To power off, slide the power switch to the "OFF" position. This will also lock the pendulum for transport.

5.2 Selecting Laser Modes

The laser features multiple modes for various applications:

• Horizontal Line: Projects a 360° horizontal line.
• Vertical Line(s): Projects one or more 360° vertical lines.
• Cross-Line: Projects intersecting horizontal and vertical lines.
• Use the mode selection buttons on the unit to cycle through the available laser configurations.

5.3 Fine Adjustment Knob

For precise alignment of plumb lines, use the fine adjustment knob located on the unit. This allows for micro-tuning to achieve exact positioning.

5.4 Using the Laser Detector (DW0892G)

For long-range visibility up to 330 ft (100m) or in bright conditions, use the included laser detector.

1. Ensure the 9V battery is installed in the detector.
2. Turn on the laser detector.
3. Move the detector along the projected laser line. The detector will emit an audible tone and display visual indicators when it detects the laser beam, helping you pinpoint its exact location.

Figure 5.1: The laser offers ±1/8 inch accuracy at 50 feet, providing high precision for demanding tasks.

Figure 5.2: Visible range extends up to 230 feet, and up to 330 feet when used with the included laser detector.

6. Maintenance and Care

• Cleaning: Keep the laser unit and detector clean. Use a soft, damp cloth to wipe surfaces. Do not use harsh chemicals or abrasive cleaners.
• Storage: When not in use, store the laser in its hard case with the pendulum locked. Store in a dry environment away from extreme temperatures.
• Battery Care: Remove the battery from the unit when storing for extended periods. Charge batteries fully before storage and periodically during storage to maintain optimal performance.
• Calibration: Regular calibration checks are recommended to ensure continued accuracy. Refer to a qualified service center for professional calibration if needed.

Figure 6.1: The durable overmolded housing provides an IP54 rating, protecting the unit from dust and water splashes (not including battery or charger).

7. Troubleshooting

8. Specifications

9. Warranty and Support

This DEWALT product is covered by a Manufacturer Warranty. For detailed warranty information, including terms and conditions, please refer to the warranty card included in your product packaging or visit the official DEWALT website.

For technical support, service, or to locate an authorized service center, please contact DEWALT customer service or visit the official DEWALT Store on Amazon.