Introduction
This manual provides essential instructions for the safe and efficient use of your Kircuit AC/DC Adapter. This adapter is designed to provide power to compatible devices, specifically Keromee VT-DH006, VTDH006, BW-116, and BW116 cordless stick vacuum cleaners. Please read this manual thoroughly before use and retain it for future reference.
Important Safety Instructions
- Do not expose the adapter to rain or moisture.
- Do not disassemble the adapter. Refer all servicing to qualified personnel.
- Ensure the adapter is used with devices that match its voltage and current specifications.
- Avoid placing the adapter in direct sunlight or near heat sources.
- Keep out of reach of children.
- Unplug the adapter from the power outlet when not in use for extended periods.
Setup
- Unpack the Adapter: Carefully remove the Kircuit AC/DC Adapter from its packaging. Inspect for any visible damage.
Image: Front view of the Kircuit AC/DC Adapter, showing the input/output specifications and brand label. The power prongs are visible on the top, and the DC barrel plug cable extends from the bottom.
- Identify Compatible Device: Ensure your device (e.g., Keromee VT-DH006 vacuum cleaner) requires a 25.2V DC power input with a barrel plug connector.
Image: Two Kircuit AC/DC Adapters shown side-by-side, illustrating the compact design and the barrel plug connector type.
- Connect to Device: Insert the barrel plug connector of the adapter into the charging port of your compatible device.
- Connect to Power Outlet: Plug the AC prongs of the adapter into a standard 100V-240V AC electrical wall outlet.
Image: The Kircuit AC/DC Adapter plugged into a white power strip on a wooden desk, demonstrating a typical usage scenario.
Operating Instructions
Once connected, the adapter will begin supplying power to your device or charging its battery. The adapter is designed for continuous operation within its specified limits.
- The adapter converts standard AC wall power (100-240V) to 25.2V DC power.
- It features built-in dynamic IC, charger IC, and power fuse for protection against overcharging and to ensure rapid charging.
- The adapter is suitable for powering or charging devices that require 25.2V DC and a barrel plug connector, such as the Keromee VT-DH006, VTDH006, BW-116, and BW116 vacuum cleaners.
Maintenance and Care
- Cleaning: Disconnect the adapter from both the power outlet and the device before cleaning. Use a soft, dry cloth to wipe the surface. Do not use liquid cleaners or sprays.
- Storage: When not in use, store the adapter in a cool, dry place, away from direct sunlight and extreme temperatures. Avoid tightly coiling the cable to prevent damage.
- Cable Care: Regularly inspect the power cord and connector for any signs of damage, such as fraying or exposed wires. If damage is found, discontinue use immediately and replace the adapter.
Image: The Kircuit AC/DC Adapter with its power cord neatly coiled, illustrating proper storage to prevent cable damage. The cord length is indicated as 6.5 ft.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Adapter not providing power. | Not properly plugged into outlet or device. Faulty outlet. Damaged adapter. | Ensure all connections are secure. Test the outlet with another device. Inspect the adapter for damage; replace if necessary. |
| Device not charging. | Incorrect adapter for the device. Device battery issue. | Verify the adapter's specifications (25.2V DC) match your device's requirements. Consult your device's manual for battery troubleshooting. |
| Adapter feels hot. | Normal operation under load. Overload or poor ventilation. | A slight warmth is normal. Ensure the adapter is in a well-ventilated area. If it's excessively hot, disconnect immediately and check for compatibility or device issues. |
Specifications
- Brand: Kircuit
- Input: 100V-240V AC, 50/60Hz
- Output: 25.2V DC
- Connector Type: Barrel Plug
- Compatible Devices: Keromee VT-DH006, VTDH006, BW-116, BW116 Cordless Stick Vacuum Cleaners
- Special Features: Built-in Dynamic IC, Charger IC & Power fuse for rapid charging and overcharge protection.
- Manufacturer: Shenzhen Waweis Technology Co., Ltd
Warranty and Support
For warranty information or technical support, please refer to the documentation provided with your purchase or contact the seller directly. This product is manufactured by Shenzhen Waweis Technology Co., Ltd under the Kircuit brand.