Franke Glass Linear LED Range Hood Instruction Manual

1. Introduction and Overview

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Franke Glass Linear LED Range Hood. Please read this manual thoroughly before using the appliance and keep it for future reference. This range hood is designed to effectively remove smoke, steam, and cooking odors from your kitchen environment.

Figure 1: Franke Glass Linear LED Range Hood (Model FGL 925 XS NP)

This image displays the Franke Glass Linear LED Range Hood, showcasing its sleek stainless steel body and transparent glass canopy. The LED lights are visible on the underside of the hood, above the control buttons.

2. Safety Instructions

Always observe the following safety precautions to reduce the risk of fire, electric shock, or injury.

• Ensure the electrical installation complies with all local and national regulations.
• Disconnect the appliance from the power supply before any cleaning or maintenance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not flambé under the range hood.
• Do not leave frying pans unattended during use, as overheated oil can ignite.
• Clean the grease filters regularly to prevent grease accumulation, which can be a fire hazard.
• Ensure adequate ventilation in the room when the range hood is used simultaneously with appliances burning gas or other fuels.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood must be at least 65 cm.

3. Package Contents

Verify that all components are present and undamaged upon unpacking. If any items are missing or damaged, contact your retailer immediately.

• Franke Glass Linear LED Range Hood unit
• Aluminium grease filters (pre-installed or separate)
• Mounting hardware (screws, wall plugs)
• Ducting adapter (if applicable)
• Instruction Manual (this document)

4. Setup and Installation

This range hood is designed for wall-mounted installation. Professional installation is recommended.

4.1. Pre-Installation Checks

• Ensure the wall structure is strong enough to support the weight of the range hood (approx. 19.9 kg).
• Verify that the electrical supply (220-240 V, 50-60 Hz) is accessible and meets safety standards.
• Plan the ducting route. The air outlet diameter is 150 mm.
• Maintain a minimum distance of 65 cm between the hob and the lowest part of the hood.

4.2. Mounting the Hood

Refer to the detailed dimension diagram below for precise measurements and mounting points. Mark the drilling positions on the wall according to the diagram and secure the mounting bracket.

Figure 2: Installation Dimensions and Technical Diagram

This diagram illustrates the precise dimensions for installing the Franke Glass Linear LED Range Hood, including width (898 mm), depth (360 mm), height (min. 725 mm - max. 1000 mm), and the 150 mm air outlet diameter. All measurements are in millimeters.

4.3. Ducting Connection

Connect the range hood to an external ventilation system using a 150 mm diameter duct. Ensure the ducting is as short and straight as possible to maximize extraction efficiency.

4.4. Electrical Connection

Connect the appliance to a grounded electrical outlet. The motor voltage is 220-240 V, 50-60 Hz. All electrical connections must be performed by a qualified electrician.

5. Operating Instructions

The Franke Glass Linear LED Range Hood features button controls for easy operation.

5.1. Power On/Off

Press the power button to turn the hood on or off.

5.2. Fan Speed Selection

The hood offers 3 standard speeds plus an intensive speed ('i').

• Speed 1: For light cooking, low steam/odor. (Efficiency: 300 m³/h, Noise: 52 dB(A))
• Speed 2: For moderate cooking, general use. (Efficiency: 450 m³/h, Noise: 61 dB(A))
• Speed 3: For heavy cooking, significant steam/odor. (Efficiency: 600 m³/h, Noise: 67 dB(A))
• Intensive Speed ('i'): For very intense cooking, maximum extraction. This speed typically operates for a set period (e.g., 5-10 minutes) before reverting to a lower speed. (Efficiency: 700 m³/h, Noise: 70 dB(A))

Press the corresponding button to select the desired fan speed.

5.3. Lighting Control

The hood is equipped with 2 LED S1001 4000K bulbs. Press the light button to turn the lights on or off.

6. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your range hood.

6.1. Cleaning the Aluminium Grease Filters

The aluminium grease filters trap airborne grease particles. They should be cleaned regularly, depending on usage (e.g., every 2-4 weeks).

1. Ensure the hood is turned off and disconnected from the power supply.
2. Locate the filter release latches (usually spring-loaded) and unclip the filters.
3. Remove the filters carefully.
4. Wash the filters by hand in hot soapy water or in a dishwasher on a low-temperature cycle.
5. Rinse thoroughly and allow them to dry completely before re-installing.
6. Re-insert the dry filters, ensuring they click securely into place.

6.2. Cleaning the Exterior Surfaces

Clean the stainless steel and glass surfaces with a soft cloth and a mild, non-abrasive cleaning agent. Do not use corrosive or abrasive cleaners, as they can damage the finish.

6.3. LED Light Replacement

LED lights have a long lifespan and typically do not require frequent replacement. If a light fails, contact a qualified technician or Franke customer support for assistance, as specialized tools or knowledge may be required.

7. Troubleshooting

Before contacting customer service, refer to the following table for common issues and their solutions.

If the problem persists after attempting these solutions, please contact Franke customer support.

8. Specifications

Detailed technical specifications for the Franke Glass Linear LED Range Hood.

• Model: FGL 925 XS NP, 325.0590.996
• Type: Wall-mounted Range Hood
• Material: Stainless Steel / Glass
• Dimensions (L x W x H): 36 x 89.8 x 25.8 cm (Product); Min. 72.5 cm - Max. 100 cm (Installation Height)
• Weight: 19.9 Kilograms
• Controls: Buttons
• Number of Speeds: 3 + 1 Intensive
• Motor Type: SP 800
• Number of Motors: 1
• Motor Power:
  • Speed 1: 130 W
  • Speed 2: 165 W
  • Speed 3: 210 W
  • Intensive: 250 W
• Extraction Efficiency:
  • Speed 1: 300 m³/h
  • Speed 2: 450 m³/h
  • Speed 3: 600 m³/h
  • Intensive: 700 m³/h
• Maximum Pressure:
  • Speed 1: 390 Pa
  • Speed 2: 470 Pa
  • Speed 3: 530 Pa
  • Intensive: 540 Pa
• Noise Level (Sound Volume):
  • Speed 1: 52 dB(A)
  • Speed 2: 61 dB(A)
  • Speed 3: 67 dB(A)
  • Intensive: 70 dB(A)
• Lighting: 2 x LED S1001 4000K bulbs
• Filter Type: Cassette, Aluminium Grease Filter (Mesh)
• Carbon Filter: Not included (for recirculation, typically purchased separately)
• Air Outlet Diameter: 150 mm
• Voltage: 220-240 V, 50-60 Hz
• Annual Energy Consumption (AEC): 72.3 kWh/year
• Energy Efficiency Class: B (A+++ to D scale)
• Fluid Dynamic Efficiency Class: B
• Light Efficiency Class: A
• Grease Filter Efficiency Class: C

9. Warranty and Support

Specific warranty details are not provided in this document. Please refer to the warranty card included with your product or visit the official Franke website for information regarding warranty coverage and terms.

For technical support, spare parts, or service inquiries, please contact Franke customer service. Keep your product model number (FGL 925 XS NP, 325.0590.996) and purchase date ready when contacting support.

You can typically find contact information on the official Franke website: www.franke.com