1. Introduction
Welcome to the world of ROBOTIME 3D Wooden Puzzles! This instruction manual provides detailed guidance for assembling and operating your ST003 Luminous Globe and LK502 Treasure Box. These intricate models offer a rewarding building experience and result in beautiful, functional pieces.
Please read all instructions carefully before beginning assembly to ensure a smooth and enjoyable building process.
Image 1.1: The ROBOTIME ST003 Luminous Globe and LK502 Treasure Box assembled.
2. Safety Information
Your ROBOTIME 3D Wooden Puzzle contains small parts and requires careful handling. Please observe the following safety guidelines:
- Choking Hazard: This product contains small parts and is not suitable for children under 3 years old. Keep all components out of reach of infants and young children.
- Sharp Edges: Some wooden pieces may have slightly sharp edges after being punched out. Use caution during assembly and consider using fine-grit sandpaper (included) to smooth edges if necessary.
- Flammable Material: The wooden components are flammable. Keep the product away from open flames, high heat sources, and direct sunlight for prolonged periods.
- Moisture: Avoid exposing the wooden parts to water or high humidity, as this can cause warping or damage.
- Adult Supervision: Adult supervision is recommended for younger builders, especially during the initial stages of assembly.
3. Package Contents
Before starting assembly, please verify that all components are present. Each puzzle kit typically includes:
- Pre-cut wooden sheets (numbered for easy identification)
- Assembly instruction booklet (specific to each model)
- Sandpaper
- Wax (for lubricating gears)
- Small accessories (e.g., screws, springs, LED light kit for ST003)
If any parts are missing or damaged, please contact ROBOTIME customer support.
4. Assembly Instructions
General tips for assembly:
- Read Ahead: Always read the current and next few steps before detaching pieces.
- Punch Out Carefully: Gently push out pieces from the wooden sheets. If a piece is stubborn, use a craft knife or utility tool to carefully cut the connecting points.
- Sand Edges: Use the included sandpaper to smooth any rough edges or burrs on the pieces. This ensures a better fit and smoother operation.
- Wax Gears: For models with moving gears (like the ST003 and LK502), apply a small amount of wax to the gear teeth and axles to reduce friction and ensure smooth movement.
- Be Gentle: Wooden pieces can be fragile. Avoid forcing pieces together. If a fit is too tight, gently sand the tab or slot until it fits snugly.
4.1. ST003: Luminous Globe Assembly
The ST003 Luminous Globe is a complex model involving gears and an internal lighting system. Follow the specific instruction booklet provided with the ST003 kit for detailed, step-by-step guidance. Key stages typically include:
- Base Assembly: Construct the intricate gear-driven base. Pay close attention to gear alignment and apply wax as instructed.
- Globe Sphere Construction: Assemble the individual segments to form the globe sphere. Ensure the internal structure for the LED light is correctly placed.
- LED Light Installation: Carefully install the LED light module and connect it according to the diagrams. Test the light before fully enclosing the globe.
- Globe Mounting: Attach the assembled globe to the base, ensuring the rotation mechanism functions smoothly.
- Outer Ring and Details: Add the outer rings, decorative elements, and any final touches.
Image 4.1: The ST003 Luminous Globe with its internal light activated, showcasing the intricate details.
4.2. LK502: Treasure Box Assembly
The LK502 Treasure Box involves assembling a functional locking mechanism. Refer to the specific instruction booklet provided with the LK502 kit for detailed, step-by-step guidance. Key stages typically include:
- Box Frame Assembly: Construct the main body of the treasure box.
- Internal Mechanism: Assemble the gears and levers that form the locking mechanism. This is the most critical part; ensure all parts move freely and are correctly aligned. Apply wax to moving parts.
- Lid Assembly: Construct the lid and integrate it with the locking mechanism.
- Combination Dial: Attach the combination dial and ensure it interacts correctly with the internal lock.
- Final Details: Add any decorative elements and test the locking function.
Image 4.2: The LK502 Treasure Box shown with its lid open, displaying the intricate wooden locking mechanism inside.
5. Operating Instructions
5.1. ST003: Luminous Globe Operation
- Rotation: The globe can be rotated manually. For continuous motion, locate the winding key on the base and gently turn it clockwise until resistance is felt. Do not overwind. The globe will then rotate slowly.
- Illumination: Locate the small switch on the base of the globe. Flip the switch to turn the internal LED light on or off. Ensure batteries (if applicable and not pre-installed) are correctly inserted.
5.2. LK502: Treasure Box Operation
- Setting the Combination: The LK502 Treasure Box typically comes with a default combination or instructions on how to set your own. Refer to the LK502 instruction booklet for precise steps on setting or changing the combination. This usually involves aligning specific numbers or symbols on the dial.
- Opening the Box: Once the combination is set, align the dial to the correct sequence. Then, turn the key or lever (if present) to unlock and open the lid.
- Closing and Locking: Close the lid firmly. Rotate the combination dial away from the set combination to lock the box. Ensure the lid is securely fastened before leaving it unattended.
Image 5.1: Users engaging with the LK502 Treasure Box, demonstrating its interactive nature.
6. Maintenance
To ensure the longevity and proper functioning of your ROBOTIME 3D Wooden Puzzles, follow these maintenance tips:
- Cleaning: Dust the models regularly with a soft, dry cloth. Avoid using water or chemical cleaners, as they can damage the wood.
- Lubrication: If gears or moving parts become stiff, apply a small amount of the included wax (or a similar non-liquid lubricant like paraffin wax) to the contact points.
- Storage: Store the models in a dry place away from direct sunlight, extreme temperatures, and high humidity to prevent warping, fading, or damage to the wood.
- Handle with Care: While durable, these are intricate models. Avoid dropping them or applying excessive force to any part.
7. Troubleshooting
If you encounter any issues during or after assembly, refer to the table below for common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Pieces don't fit together | Rough edges; incorrect orientation; wrong piece. | Gently sand edges; check instruction diagrams for correct orientation; verify piece number. |
| Gears or mechanism are stiff/stuck | Lack of lubrication; misaligned gears; burrs on pieces. | Apply wax to gears and axles; re-check gear alignment; sand any rough spots. |
| ST003 light not working | Batteries dead/incorrectly inserted; loose connection; faulty LED. | Check battery polarity and charge; ensure all wires are securely connected; contact support if LED is faulty. |
| LK502 combination not working | Incorrect combination; internal mechanism misalignment. | Double-check the combination; refer to the LK502 manual for resetting or troubleshooting the lock mechanism. |
8. Specifications
| Feature | ST003 Luminous Globe | LK502 Treasure Box |
|---|---|---|
| Model Number | ST003 | LK502 |
| Material | High-quality Plywood | |
| Recommended Age | 14+ (with adult supervision for younger builders) | |
| Approx. Assembly Time | 4-8 hours | 4-6 hours |
| Special Features | Internal LED light, self-rotating mechanism | Functional combination lock, storage compartment |
9. Warranty and Support
ROBOTIME products are manufactured with high standards of quality. If you encounter any issues with your puzzle bundle, such as missing or defective parts, or require assembly assistance, please contact ROBOTIME customer support.
For the most up-to-date warranty information and contact details, please refer to the official ROBOTIME website or the contact information provided in your product packaging.
