Introduction
The FLIPSKY 75100 Pro V2.0 is an advanced Electronic Speed Controller (ESC) designed for a wide range of electric vehicles and robotics applications. This includes electric skateboards, scooters, electric bicycles, robots, and various DIY off-road vehicles. It is built upon the VESC 75 series architecture, offering robust performance with features such as overheat and overcurrent protection, and regenerative braking capabilities.
The controller features an aluminum PCB for efficient heat dissipation, ensuring stable operation even under demanding conditions. It supports a maximum working voltage of 84V (suitable for 4-20S battery configurations) and provides a continuous current of 100A. The integrated Bluetooth module allows for convenient parameter adjustment and real-time data monitoring via the VESC TOOL application, eliminating the need for external modules. A key switch is also included for power on/off functionality.
Product Overview
The FLIPSKY 75100 Pro V2.0 ESC is a compact and powerful unit, designed for seamless integration into your projects. Below are visual representations and descriptions of the product and its components.
Figure 1: The FLIPSKY 75100 Pro V2.0 ESC controller, shown with its integrated key switch and various wiring harnesses for connection to battery, motor, and control signals.
Figure 2: Physical dimensions of the ESC unit. The controller measures L103mm x W58mm x H27.7mm, indicating its compact design for various installations.
Figure 3: Detail showing the upgraded Bluetooth module function. No external Bluetooth module is required, simplifying setup and enabling convenient wireless parameter adjustment and real-time data reading.
Figure 4: Examples of applications for the ESC, including electric skateboards, scooters, ebikes, and other DIY electric vehicles, highlighting its versatility.
Specifications
| Feature | Description |
|---|---|
| Firmware | 6.02 (firmware update supported) |
| Size | L103mm*W58mm*H27.7mm |
| Voltage Range | 14-84V (4-20S) |
| Continuous Current | 100A |
| BEC | 5V@1.5A |
| Supported Modes | BLDC square wave mode control and FOC sine wave mode |
| ERPM | 150000 |
| Control Interface Ports | USB, CAN, UART |
| Supported Sensors | ABI, HALL, AS5047, AS5048A |
| Input Set Support | PPM, ADC, NRF, UART |
| Wire Size | 10AWG (75100 Pro) |
| Programmable | Yes |
| Regenerative Capacity | Yes |
| Phase Filter | Yes |
| Power Switch Button | Red |
Setup
Before using the FLIPSKY 75100 Pro V2.0, it is crucial to properly configure its parameters using the VESC TOOL. The factory firmware version is 6.02. Ensure you use the correct firmware version for your application to prevent potential damage to the ESC.
Important: Except for Apple computers, other computer firmware can be downloaded from our official website. Apple computer users may need to purchase the VESC TOOL application from the Apple App Store. Always refer strictly to the provided wiring diagram for safe product use.
Figure 5: Detailed wiring diagram for the ESC, showing connections for battery, motor, power switch, Hall sensors, USB, and communication ports. Pay special attention to 3.3V and 5V connections to avoid short-circuits.
Figure 6: Illustration of supported control modes (Sine Wave and Square Wave) and guidance on choosing an ESC and adjusting parameters within the VESC TOOL.
Firmware Update and Parameter Adjustment
When connecting the controller for the first time, the VESC TOOL may indicate inconsistent firmware versions. It is essential to update the firmware to a consistent version before proceeding with parameter adjustments. Different firmware versions can lead to parameter discrepancies and potentially damage the ESC.
For detailed instructions on using the VESC TOOL for setup and parameter adjustment, please refer to the following official videos:
Video 1: A comprehensive guide to setting up and configuring the 75100 Pro V2.0 using the VESC TOOL. This video demonstrates the process of selecting motor types and adjusting various parameters for optimal performance.
Video 2: This video provides additional insights into the setup of the 75100 Pro V2.0, focusing on specific configurations and advanced settings within the VESC TOOL for different applications.
Operating Instructions
The FLIPSKY 75100 Pro V2.0 operates within a voltage range of 14-84V (safe for 4-20S battery configurations). It provides a continuous current of 100A. The integrated BEC (Battery Eliminator Circuit) outputs 5V at 1.5A, ensuring stable power for your receiver. Ensure the receiver's current draw does not exceed 1.5A.
When using any throttle handle under ADC control, always ensure that the positive pole of the power supply is connected to the 3.3V pin, not the 5V pin, to prevent damage.
Figure 7: Visual representation emphasizing the 100A continuous current rating. It is critical not to exceed the specified voltage range to prevent damage to the ESC.
Maintenance
Proper maintenance ensures the longevity and reliable performance of your FLIPSKY 75100 Pro V2.0 ESC. Adhere to the following guidelines:
- Handle with Care: The ESC seat is designed for secure connections, but avoid excessive force when plugging or unplugging connectors to prevent them from falling off or damaging wires.
- Secure Connections: Ensure that all battery and motor ports are firmly welded. Loose connections can lead to intermittent power, overheating, and potential damage to the ESC or connected components.
- Regular Inspection: Periodically inspect all wiring and connections for signs of wear, fraying, or corrosion. Address any issues promptly.
- Cleanliness: Keep the ESC clean and free from dust, dirt, and moisture. While the aluminum casing aids in heat dissipation, excessive debris can hinder cooling.
Troubleshooting
If you encounter issues with your FLIPSKY 75100 Pro V2.0 ESC, consider the following common problems and solutions:
- Firmware Inconsistency: If the VESC TOOL displays a pop-up indicating inconsistent versions upon connection, you must update the firmware to a consistent version before adjusting parameters. Failure to do so can lead to incorrect operation or damage.
- ESC Burnout: Operating the ESC outside its specified voltage range (14-84V) can cause it to burn out. Always verify your battery voltage is within the safe operating limits (4-20S).
- Short-Circuiting: Incorrect wiring, especially short-circuiting the 3.3V and 5V pins, can damage the ESC. Double-check all connections against the wiring diagram before powering on.
- Motor Malfunction: If the motor is not functioning correctly, ensure all Hall sensor and phase wires are properly connected and securely welded. Incorrect motor parameters in VESC TOOL can also cause issues; re-run motor detection if necessary.
If problems persist, refer to the official support resources or contact FLIPSKY customer service.
Warranty and Support
The FLIPSKY 75100 Pro V2.0 comes with a 2-month warranty from the date of purchase. Please retain your proof of purchase for warranty claims.
For further assistance, technical support, or if you require additional guidance beyond this manual, please utilize the following resources:
- Official Website: https://flipsky.net/
- Email Support: flipskytech@outlook.com
- Video Resources: Additional instructional videos are available online. If you still have questions after reviewing the manual and available videos, please contact us for relevant video support.
