Franke ATL-SD Atlas Deck Mounted Soap Dispenser Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Franke ATL-SD Atlas Deck Mounted Soap Dispenser. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product. Retain this manual for future reference.

The Franke ATL-SD Atlas is a single-hole, top-refill soap dispenser designed for convenient dispensing of liquid soap or lotion directly from your sink countertop, helping to reduce clutter.

2. Product Features

• Model: ATL-SD
• Capacity: Approximately 11.5 fluid ounces (340 ml)
• Material: Durable Brass and Stainless Steel construction (Stainless Steel 316 finish)
• Design: Deck-mounted, single-hole installation
• Refill Method: Convenient top-fill design, allowing refills from above the counter
• Dispensing: Smooth pump mechanism for liquid soap or lotion

3. Setup and Installation

Before beginning installation, ensure you have all necessary components and tools. If you are unsure about any step, it is recommended to consult a qualified professional.

Image 1: Franke ATL-SD Atlas Deck Mounted Soap Dispenser. This image displays the complete soap dispenser unit, featuring a brushed stainless steel finish. The main body is cylindrical, with a horizontal spout extending from the upper portion. A circular base provides stability for deck mounting.

Required Tools (Not Included):

• Adjustable wrench or pliers
• Screwdriver (if applicable for mounting hardware)
• Sealant (plumber's putty or silicone, if required for watertight seal)
• Drill with appropriate bit (if drilling a new hole in countertop)

Installation Steps:

1. Prepare the Countertop: Ensure there is an existing hole in your countertop or sink deck, typically 1 to 1.5 inches in diameter. If drilling a new hole, follow manufacturer guidelines for your countertop material and ensure proper clearance underneath.
2. Disassemble the Dispenser: Separate the pump head and spout assembly from the mounting shank and bottle.
3. Install Mounting Shank: Insert the threaded mounting shank through the hole in the countertop from above.
4. Secure from Below: From underneath the countertop, slide the rubber washer, then the metal washer, and finally thread the mounting nut onto the shank. Tighten the nut securely with an adjustable wrench or pliers, ensuring the dispenser is oriented correctly. Do not overtighten.
5. Attach Soap Bottle: Screw the soap bottle onto the threaded end of the mounting shank from underneath the countertop. Ensure it is hand-tightened to prevent leaks.
6. Reassemble Pump Head: Place the pump head and spout assembly back into the top of the mounting shank. It should sit flush with the countertop.

4. Operating Instructions

Initial Fill and Priming:

1. Remove Pump Head: Gently pull the pump head and spout assembly straight up from the dispenser base on the countertop.
2. Fill Bottle: Pour liquid hand soap or lotion directly into the bottle from the top opening. Do not overfill; leave some space for the pump mechanism.
3. Replace Pump Head: Insert the pump head and spout assembly back into the base, ensuring it is seated properly.
4. Prime the Pump: Press the pump head several times until soap or lotion begins to dispense. It may take multiple presses to draw the liquid up the tube.

Dispensing Soap:

To dispense soap, simply press down on the pump head. The spout will deliver a measured amount of liquid soap or lotion.

5. Maintenance

Cleaning:

• Regularly wipe the exterior of the dispenser with a soft, damp cloth and mild soap.
• Avoid using abrasive cleaners, scouring pads, or harsh chemicals, as these can damage the stainless steel finish.
• For stubborn spots, use a stainless steel cleaner specifically designed for kitchen fixtures, following the product's instructions.

Preventing Clogs:

• Use only liquid hand soap or lotion. Avoid using granular or abrasive soaps.
• If the dispenser becomes difficult to pump, remove the pump head and rinse it thoroughly under warm water to clear any dried soap.
• Periodically, you may wish to flush the pump mechanism by filling the bottle with warm water and pumping it through until clear.

6. Troubleshooting

Dispenser Not Pumping:

• Check Soap Level: Ensure the bottle contains enough liquid soap or lotion.
• Prime the Pump: Press the pump head repeatedly to draw liquid up the tube.
• Clear Clog: Remove the pump head and rinse it under warm water. If the dip tube is clogged, clear it with a thin brush or by flushing with water.
• Reassemble Correctly: Ensure the pump head is fully seated in the base.

Leaking from Base:

• Check Bottle Connection: Ensure the soap bottle is securely tightened to the mounting shank from underneath the counter.
• Check Mounting Nut: Verify that the mounting nut under the counter is tight, securing the dispenser firmly to the countertop.

Difficulty Pumping:

• Soap Consistency: Some very thick soaps or lotions may be difficult to pump. Consider diluting slightly with water if safe for the product.
• Clean Pump: Follow the cleaning steps in the Maintenance section to ensure no dried soap is impeding the mechanism.

7. Specifications

8. Warranty and Support

For specific warranty information regarding your Franke ATL-SD Atlas Deck Mounted Soap Dispenser, please refer to the documentation included with your purchase or visit the official Franke website. If you require technical assistance or have questions not covered in this manual, please contact Franke customer support directly.

Contact information can typically be found on the manufacturer's website or on your product packaging.