Introduction
The SnapPower GuideLight PLUS transforms your standard horizontal electrical outlet into a convenient LED night light. This innovative cover plate integrates an LED light bar and a light sensor, providing subtle illumination without occupying an outlet. It is designed for horizontal décor style outlets and offers adjustable brightness settings.
Key features include:
- Horizontal Design: LED lighting is adapted along the long side, ideal for accent lighting on kitchen islands, countertops, shelves, and bathrooms.
- Adjustable Brightness: Features a Bright, Dim, and Off switch to customize light intensity.
- Automatic Operation: A built-in dusk-to-dawn light sensor ensures the night light activates only when it's dark.
- Easy Installation: Designed for simple, safe installation without the need for wiring, batteries, or special tools.
Important Note: This product is for use with Décor style outlets only. It is NOT compatible with GFCI outlets or light switches. Ensure your Décor outlet has screws on the side before purchase and installation.
Setup and Installation
Installing your SnapPower GuideLight PLUS is a straightforward process. Please follow these steps carefully to ensure safe and proper installation.
Safety Precautions:
- ALWAYS turn off power to the outlet at the circuit breaker before beginning installation.
- Verify the power is off by attempting to use a device in the outlet.
- If you are unsure about electrical work, consult a qualified electrician.
Installation Steps:
- Turn Off Power: Locate the circuit breaker controlling the outlet where you intend to install the GuideLight PLUS and switch it to the OFF position.
- Remove Existing Cover Plate: Unscrew and remove the existing wall plate from your horizontal Décor outlet.
- Inspect Outlet: Ensure your outlet is a standard Décor style with side screws. The GuideLight PLUS draws power from the side terminals of the outlet. If the terminals are covered with electrical tape, carefully remove it to allow contact.
- Position GuideLight PLUS: Align the SnapPower GuideLight PLUS cover plate over your outlet. The two conductive prongs on the back of the GuideLight PLUS should slide into contact with the side terminals of the electrical outlet.
This image displays the rear of the GuideLight PLUS cover plate, highlighting the two conductive prongs that connect to the outlet's internal terminals to draw power. The design ensures a clean, wire-free installation.
- Secure the Plate: Use the provided screw to fasten the GuideLight PLUS cover plate to the outlet. Do not overtighten.
- Restore Power: Once the plate is securely installed, return to your circuit breaker and switch the power back ON.
- Test Functionality: The GuideLight PLUS should illuminate if the room is dark and the switch is set to Bright or Dim.
Operating Instructions
The SnapPower GuideLight PLUS is designed for simple, automatic operation with customizable brightness.
Light Sensor:
The GuideLight PLUS features an integrated light sensor. This sensor detects ambient light levels and automatically turns the LED night light ON when the room is dark and OFF when it is bright. This ensures efficient energy use and hands-free operation.
Brightness Switch:
On the bottom edge of the GuideLight PLUS cover plate, you will find a small switch with three settings: Bright, Dim, and Off.
- Bright: Provides maximum illumination for clear visibility in dark areas.
- Dim: Offers a softer, more subtle glow, ideal for hallways or bedrooms where minimal light is desired.
- Off: Disables the LED night light completely, regardless of ambient light conditions.
Adjust the switch to your preferred setting. The light sensor will then control the ON/OFF function based on the selected brightness level (Bright or Dim).
The GuideLight PLUS is shown installed on a horizontal electrical outlet in a kitchen backsplash, casting a soft, downward glow onto the countertop. This demonstrates its integrated design and function as a discreet night light.
Maintenance
The SnapPower GuideLight PLUS requires minimal maintenance.
- Cleaning: To clean the surface of the cover plate, gently wipe it with a soft, dry, or slightly damp cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the finish or electronic components.
- No Bulb Replacement: The LED light source is designed for a long lifespan (25+ years) and is not user-replaceable.
Troubleshooting
If your SnapPower GuideLight PLUS is not functioning as expected, please refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. |
|
|
| Light stays on during the day. |
|
|
| Light flickers or is inconsistent. |
|
|
Specifications
| Brand | SnapPower |
| Model Number | Horizontal | Decor | Black |
| Style | Décor |
| Color | Black |
| Finish Type | Matte |
| Base Material | Plastic |
| Light Source Type | LED |
| Power Source | Electrical Outlet |
| Mounting Type | Wall Mount (Screw-In) |
| Lighting Method | Downlight |
| Indoor/Outdoor Usage | Indoor |
| Item Weight | 1.5 Ounces |
| Number of Items | 2 (in this pack) |
| Included Components | Wall Plate, Screw, User Manual |
Warranty and Support
Specific warranty details are not provided in the product information. For warranty inquiries or technical support, please contact SnapPower directly through their official website or customer service channels.
You can typically find support information on the manufacturer's website: www.snappower.com
