SteFik Replacement Accessory Set

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your SteFik Replacement Accessory Set, designed for Zigma Spark 980 and 981 Robot Vacuums. Regular replacement and maintenance of these accessories ensure optimal cleaning performance and extend the lifespan of your robot vacuum.

Package Contents

Your SteFik Replacement Accessory Set may include the following components. Please verify the contents against your specific purchase.

• HEPA Filters
• Side Brushes
• Mop Cloths

Image: Overview of the SteFik Replacement Accessory Set, showing multiple HEPA filters, blue mop cloths, and yellow-tipped side brushes.

Setup and Installation

Before installing any accessories, ensure your Zigma Spark robot vacuum is powered off and disconnected from its charging base.

1. Installing Side Brushes

1. Turn the robot vacuum upside down.
2. Locate the existing side brushes. If present, gently pull them upwards to remove.
3. Align the new side brushes with the corresponding posts (L for left, R for right) on the robot's underside.
4. Press the new brushes down firmly until they click into place.

Image: Close-up of two replacement side brushes, featuring yellow bases and black bristles.

2. Installing HEPA Filters

1. Open the dust bin compartment on your robot vacuum.
2. Remove the dust bin from the robot.
3. Open the dust bin cover to access the filter slot.
4. Remove the old HEPA filter.
5. Insert the new HEPA filter into the designated slot, ensuring it fits snugly.
6. Close the dust bin cover and reinsert the dust bin into the robot vacuum.

Image: A single replacement HEPA filter, showing its pleated design for efficient air filtration.

3. Attaching Mop Cloths

1. Locate the water tank or mop module on your robot vacuum.
2. If an old mop cloth is attached, remove it.
3. Align the new mop cloth with the Velcro strips or attachment points on the water tank/mop module.
4. Press firmly to secure the mop cloth in place.

Image: A single blue mop cloth, designed for wet cleaning functions of the robot vacuum.

Operating with New Accessories

Once the replacement accessories are installed, your Zigma Spark robot vacuum is ready for operation. The new components will contribute to improved cleaning efficiency:

• Side Brushes: Effectively sweep debris from edges and corners into the main cleaning path.
• HEPA Filters: Capture fine dust particles and allergens, improving air quality.
• Mop Cloths: Provide wet cleaning for hard floors, removing stains and grime.

Maintenance

Regular cleaning and timely replacement of accessories are crucial for maintaining your robot vacuum's performance.

1. Side Brushes

• Cleaning: Remove hair and debris tangled around the brushes regularly (e.g., weekly).
• Replacement: Replace every 3-6 months, or sooner if visibly worn or damaged.

2. HEPA Filters

• Cleaning: Gently tap the filter against a trash can to remove accumulated dust. Do not wash HEPA filters with water, as this can damage the filter material.
• Replacement: Replace every 2-3 months, or more frequently if your home has pets or high dust levels.

3. Mop Cloths

• Cleaning: Remove and wash the mop cloth after each use. Hand washing with mild detergent is recommended. Allow to air dry completely before reattaching.
• Replacement: Replace every 1-3 months, or if the cloth becomes heavily stained or loses its cleaning effectiveness.

Troubleshooting

If you experience issues after replacing accessories, consider the following:

• Reduced Cleaning Performance: Check if the HEPA filter is clogged or if the side brushes are tangled with hair. Ensure all components are installed correctly.
• Unusual Noise: Verify that side brushes are free of obstructions and properly seated.
• Mop Cloth Not Wetting: Ensure the water tank is filled and the mop cloth is correctly attached to the module.

Specifications

Image: Technical diagram illustrating the dimensions (9.7cm x 6.4cm) and weight (9g) of a single HEPA filter.

Warranty and Support

For specific warranty information regarding your SteFik Replacement Accessory Set, please refer to the purchase documentation or contact the seller directly. If you encounter any issues not covered in this manual, please reach out to the manufacturer or seller for further assistance.