Tapitapa Arched Floor Lamp User Manual

Introduction

Thank you for purchasing the Tapitapa Arched Floor Lamp. This manual provides essential information for the safe and efficient use of your new lamp. Please read these instructions carefully before assembly and operation, and retain them for future reference.

Figure 1: The Tapitapa Arched Floor Lamp, showcasing its elegant design with a black metal frame and smoked glass shade.

Safety Instructions

To ensure safe operation and prevent damage, please observe the following safety precautions:

• Always disconnect the lamp from the power supply before cleaning, maintenance, or bulb replacement.
• This lamp is designed for indoor use only (IP20 rating). Do not expose it to moisture or extreme temperatures.
• Ensure the power supply voltage matches the lamp's requirements (230 Volt).
• Do not exceed the maximum wattage for the bulb (60 Watt for E27 socket).
• Keep the lamp away from flammable materials.
• If the power cord is damaged, it must be replaced by a qualified electrician to avoid hazards.
• Handle the glass shade with care to prevent breakage.

Package Contents

Carefully unpack all components and check against the list below. If any parts are missing or damaged, contact customer support immediately.

Figure 2: All components included in the package for assembly.

• Marble Base
• Lamp Pole Sections (multiple, including curved arm)
• Smoked Glass Shade
• E27 Lamp Holder Assembly with Power Cord and Foot Switch
• Mounting Hardware (screws, washers, wrench if applicable)
• User Manual (this document)

Note: Light bulb is not included and must be purchased separately.

Setup and Assembly

Follow these steps to assemble your Tapitapa Arched Floor Lamp:

1. Attach the Pole to the Base: Carefully insert the bottom section of the lamp pole into the hole in the marble base. Secure it using the provided screw and washer from underneath the base. Ensure it is stable and upright.
   

   Figure 3: Detail of the sturdy marble base.

2. Assemble Pole Sections: Connect the remaining pole sections, including the curved arm, by screwing them together clockwise. Ensure all connections are tight and secure. Route the power cord through the pole as you assemble.
3. Install the Lamp Holder: Attach the E27 lamp holder assembly to the end of the curved arm. Make sure the wiring is not pinched.
4. Insert the Light Bulb: Screw an E27 bulb (max. 60W) into the lamp holder. Do not overtighten.
5. Attach the Glass Shade: Carefully place the smoked glass shade over the bulb and secure it to the lamp holder assembly. Ensure it is seated properly and stable.
   

   Figure 4: The E27 socket and glass shade attachment point.

6. Position the Lamp: Place the lamp in your desired location, ensuring the power cord can reach an outlet without being strained or creating a tripping hazard.

Operating Instructions

Your Tapitapa Arched Floor Lamp is designed for simple operation:

• Power On/Off: The lamp is equipped with a convenient foot switch located on the power cord. Simply press the switch with your foot to turn the lamp on or off.
  

  Figure 5: The integrated foot switch for easy operation.

• Adjustable Arm: The arched arm of the lamp features an adjustable joint near the shade, allowing you to slightly modify the angle of the light. Gently pivot the arm to achieve your desired lighting direction.
  

  Figure 6: Lamp dimensions and adjustable arm feature.

Maintenance

Regular maintenance will help prolong the life and appearance of your lamp:

• Cleaning: Disconnect from power. Wipe the metal frame and marble base with a soft, dry cloth. For the glass shade, use a soft, damp cloth and mild glass cleaner if necessary, then dry thoroughly. Avoid abrasive cleaners or solvents.
• Bulb Replacement: Ensure the lamp is unplugged and the bulb has cooled down. Unscrew the old E27 bulb and replace it with a new one, ensuring it does not exceed 60W.
• Inspections: Periodically check the power cord for any signs of damage or fraying. Ensure all connections remain tight.

Troubleshooting

If you encounter issues with your lamp, refer to the following common problems and solutions:

If the problem persists after trying these solutions, please contact customer support.

Specifications

Warranty and Support

Your Tapitapa Arched Floor Lamp is manufactured by hofstein. For any questions, technical support, or warranty claims, please contact the seller or manufacturer directly.

Please retain your proof of purchase for warranty purposes. The return policy for this product is 30 days from the date of purchase.

For more information about hofstein products, you may visit their brand store: hofstein Brand Store