Introduction
The BENINCA to.GO2WV is a 2-channel, 433.92 MHz rolling code transmitter designed for use with compatible BENINCA gate and garage door openers. This remote control combines a modern design with robust functionality, offering a reliable solution for controlling two distinct automation systems. It is an evolved remote control concept, replacing older models like the T2WV, and is also available with sequential code for multiple code storage.
Package Contents
- 2 x BENINCA to.GO2WV Remote Controls
- Batteries (pre-installed or included separately)
- Instruction Manual (this document)
Product Overview
Image: The BENINCA to.GO2WV remote control. This black, ergonomic remote features two distinct light grey buttons on its face, designed for controlling two separate channels. The "to.GO" branding is subtly embossed on the lower left side of the remote's body.
The to.GO2WV remote is designed for ease of use with its ergonomic shape and two clearly defined buttons. Each button corresponds to a channel, allowing control of two different automation systems. The rolling code technology ensures enhanced security for your gate or garage door.
Setup and Programming
To ensure proper operation, the to.GO2WV remote must be programmed to your BENINCA receiver. The programming procedure typically involves accessing the receiver unit and initiating a pairing sequence. Refer to your specific BENINCA receiver's manual for detailed programming instructions, as procedures may vary slightly between models.
General Programming Steps (Consult Receiver Manual for Specifics):
- Access the Receiver: Locate your BENINCA gate or garage door opener's receiver unit. This may require opening the control panel.
- Activate Programming Mode: Press and hold the programming button (often labeled "PROG," "MEMO," or similar) on the receiver until an indicator light (LED) changes state or a specific sound is heard.
- Transmit Code from New Remote: While the receiver is in programming mode, press and hold the desired button on your new to.GO2WV remote for a few seconds.
- Confirm Pairing: The receiver's indicator light should confirm successful pairing (e.g., flash rapidly, turn solid, or turn off). Release the button on the remote.
- Test Operation: After programming, test the remote's functionality from a safe distance to ensure it operates the gate or garage door correctly.
- Program Second Channel (if applicable): Repeat the process for the second button if you wish to control another device.
Note: If you are replacing an existing BENINCA remote, some receivers may support a "remote-to-remote" cloning procedure. Consult your receiver's manual for this advanced option.
Operating the Remote
Once programmed, operating the BENINCA to.GO2WV remote is straightforward:
- Opening/Closing: Press the programmed button corresponding to the gate or garage door you wish to operate. A single press typically initiates the open or close cycle.
- Stopping: Pressing the button again during an open or close cycle may stop the movement, depending on your receiver's configuration.
- Range: Ensure you are within the operational range of your receiver. Obstructions and environmental factors can affect signal strength.
Maintenance
The BENINCA to.GO2WV remote is designed for durability, but proper care will extend its lifespan:
- Cleaning: Wipe the remote with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- Battery Replacement: When the remote's range decreases significantly or the indicator light (if present) fails to illuminate, it's time to replace the battery. The to.GO2WV typically uses a standard coin cell battery (e.g., CR2032). To replace, carefully open the remote's casing (often by prying gently along the seam with a small flat-head screwdriver) and replace the battery, observing polarity.
- Storage: Store the remote in a dry place, away from extreme temperatures and direct sunlight.
- Avoid Impact: Do not drop the remote or subject it to strong impacts.
Troubleshooting
If you encounter issues with your BENINCA to.GO2WV remote, refer to the table below for common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not working / No response |
|
|
| Reduced operating range |
|
|
| Remote works intermittently |
|
|
If these solutions do not resolve the issue, please contact customer support or a qualified technician.
Specifications
| Feature | Detail |
|---|---|
| Model | to.GO2WV |
| Frequency | 433.92 MHz |
| Coding Type | Rolling Code |
| Channels | 2 |
| Compatible Devices | BENINCA Receivers |
| Special Feature | Ergonomic Design |
| Power Source | Battery (e.g., CR2032 coin cell) |
Compatibility
The BENINCA to.GO2WV remote control is 100% compatible with the following BENINCA remote models and systems:
- TO.GO 4WV
- T2WV
- T4WV
- CUPIDO-2
- CUPIDO-4
- BENINCA IO.2WV (all colors)
It is designed to work seamlessly with BENINCA gate and garage door opener receivers operating on the 433.92 MHz rolling code frequency.
Warranty Information
For specific warranty terms and conditions, please refer to the warranty documentation provided with your purchase or contact the original seller. Warranty coverage typically addresses manufacturing defects and material flaws under normal use.
Customer Support
If you have any questions regarding the setup, operation, or troubleshooting of your BENINCA to.GO2WV remote control, please contact the seller or the BENINCA customer support directly. Provide your product model number and a detailed description of your issue for efficient assistance.
We are fully committed to 100% customer satisfaction.