1. Product Overview
The Adviace 80709 Convection Blower is a replacement room blower designed for various pellet stove models, including those from US Stove, Ashley, and King. This component is crucial for circulating heated air from the stove into the living space, ensuring efficient heat distribution.
Image 1: The Adviace 80709 Convection Blower, a replacement part for pellet stoves, shown with its motor and fan assembly.
2. Compatible Models
This convection blower (part number 80709, also replaces 80834) is compatible with the following pellet stove models:
- For US Stove Company pellet stoves: 5501S, 5710, KP60-XH, US5517-P
- For Ashley pellet stoves: AP5501S, AP5710, AP5780, AP60
- For King pellet stoves: KP60
- For Vogelzang pellet stoves: VG5717-P, VG60
- For Breckwell Gas Fireplace models: BH3024FP, BH6113LFP
Image 2: Examples of compatible pellet stove models, including Ashley AP5710 and US Stove 5501S.
3. Key Features
- 100% Sealed Ball Bearing Motor: Designed for longevity and quiet operation, outperforming sleeve bearing blowers. Sealed bearings require no additional maintenance and are less susceptible to heat effects.
- Exact Replacement Part: Engineered to fit and function as a direct replacement for original parts.
- Durable Construction: The blower includes rubber grommets on both ends where the bearings ride, preventing them from drying out due to heat.
- Technical Specifications: Operates at 115 Volts, 60Hz, with 1.25 Amps. Features a two-wire hookup with 1/4" female insulated terminals.
Image 3: Close-up view highlighting the rubber grommets on the blower, designed to protect bearings from heat.
4. Setup and Installation
Installation of the convection blower typically involves replacing the existing unit within your pellet stove. While specific steps may vary by stove model, general guidelines include:
- Safety First: Always ensure the pellet stove is completely unplugged from its power source and has cooled down before beginning any installation or maintenance.
- Access the Blower: Locate the existing convection blower within your stove. This may require removing access panels or other components. Refer to your specific stove's manual for detailed instructions.
- Disconnect Wiring: Carefully disconnect the two-wire hookup from the old blower. Note the orientation if necessary, though this blower uses standard 1/4" female insulated terminals.
- Remove Old Blower: Unmount and remove the old blower unit.
- Install New Blower: Position the new Adviace 80709 blower in place and secure it using the appropriate mounting hardware.
- Connect Wiring: Reconnect the two wires to the new blower's terminals.
- Reassemble Stove: Replace any access panels or components that were removed.
- Test: Plug the stove back in and test the new blower's operation.
It is recommended to consult a qualified technician if you are unsure about any part of the installation process.
5. Operating Principles
The convection blower is an integral part of your pellet stove's heating system. Its primary function is to draw cool air from the room, pass it over the hot heat exchanger within the stove, and then blow the now heated air back into the room. This process ensures efficient transfer of heat from the combustion chamber to your living space, maximizing the stove's heating capacity and comfort.
Image 4: A pellet stove in a living room setting, illustrating where the convection blower would function to distribute heat.
6. Maintenance
Regular maintenance of your convection blower is essential for optimal performance and longevity. Follow these recommendations:
- Seasonal Cleaning of Fan Paddles: It is recommended to clean the fan paddles every heating season. With the blower removed from the stove, use a dry paint brush or compressed air to remove any accumulated dust or debris.
- Annual Blower Fin Cleaning: Annually, clean the blower fins to ensure no dust or debris impedes airflow. This helps maintain efficiency and prevents strain on the motor.
Always ensure the stove is cool and disconnected from power before performing any maintenance.
7. Troubleshooting
If you experience issues with your pellet stove's heating performance, the convection blower may be a contributing factor. Here are common problems and how this replacement blower can help:
| Symptom | Potential Cause (Old Blower) | Solution (New Adviace 80709 Blower) |
|---|---|---|
| Loud squeaking noise from stove | Worn-out bearings in the original blower. | The new Adviace 80709 blower features 100% sealed ball bearings designed for quiet operation, significantly reducing or eliminating squeaking. |
| Stove not burning efficiently or overheating | Reduced airflow due to a failing or inefficient old blower. | A new, properly functioning convection blower ensures optimal airflow, leading to a better burn and preventing overheating, improving overall stove efficiency. |
Image 5: Visual comparison illustrating the difference in performance and noise between an old, worn blower and a new replacement blower.
8. Specifications
| Attribute | Detail |
|---|---|
| Model Number | 80709 (Replaces 80834) |
| Voltage | 115 Volts |
| Cycles | 60Hz |
| Amperage | 1.25 Amps |
| Wattage | 143.75 watts |
| Overall Size (Approx.) | 17-1/2" Length x 3-3/4" Width x 4-1/4" Height |
| Wiring | Two wire hook up with 1/4" female insulated terminals |
| Bearing Type | 100% Sealed Ball Bearing |
| Blade Material | Plastic |
| Item Weight | 3.85 pounds |
| Indoor/Outdoor Usage | Indoor |
Image 6: Diagram illustrating the technical specifications and approximate dimensions of the convection blower.
9. Warranty and Support
The Adviace 80709 Convection Blower comes with a 1-year manufacturer warranty. For any questions or support regarding this product, please contact the manufacturer or your point of purchase.