1. Introduction
Thank you for choosing the Akozon B810 Electric Bicycle Display. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your display unit. Please read this manual thoroughly before use to ensure optimal performance and longevity of the product.
2. Safety Information
- Always ensure the power is off before installing or disconnecting the display unit.
- Avoid exposing the display to extreme temperatures, direct sunlight for prolonged periods, or corrosive substances.
- Do not attempt to disassemble or modify the display unit. This may void the warranty and cause damage.
- Keep the display unit dry. Although it is waterproof, prolonged immersion or high-pressure water jets should be avoided.
- Ensure all cable connections are secure to prevent short circuits or intermittent operation.
3. Product Overview
The Akozon B810 is a compact and durable display unit designed for electric bicycles and scooters. It provides essential information and control functions for your electric vehicle.
Key Features:
- Clear LED battery indicator.
- Power control with multiple assist levels.
- Automatic sleep function after 10 minutes of inactivity.
- Fault indication for quick diagnosis.
- Lightweight, waterproof, and durable construction.
Components:
The display unit features an ON/OFF button, a MODE button for power assist levels, a '6km' button (typically for walk-assist), and LED indicators for battery level and power assist mode.
Close-up view of the Akozon B810 display unit, highlighting the ON/OFF, MODE, and 6km buttons, along with the LED indicators for power and assist levels.
The Akozon B810 control module, featuring circular buttons and an extended cable for connection to the e-bike or scooter system.
4. Setup and Installation
Mounting the Display:
- Identify a suitable location on your handlebar, typically near the grip, that allows for easy access and visibility.
- Use the integrated clamp on the back of the display unit to secure it to the handlebar. Ensure it is tightened firmly but do not overtighten to avoid damage.
The Akozon B810 display unit shown mounted on the handlebar of a white electric bicycle.
Wiring Connection:
The B810 display connects to your electric bicycle or scooter controller via a 5-wire cable. Ensure correct polarity and connection for proper function.
Detailed view of the 5-wire cable connector and its corresponding functions for the Akozon B810 display.
| Sequence No. | Wire Color | Function |
|---|---|---|
| 1 | Red (Vcc) | Display Power cable |
| 2 | Blue (Ds) | Controller Power Cable |
| 3 | Black (GND) | Display Ground cable |
| 4 | Green (RX) | Display Data Receiving Wire |
| 5 | Yellow (TX) | Display Data Sending Wire |
Connect the 5-wire cable from the display unit to the corresponding port on your e-bike or scooter controller. Ensure the connector is fully seated and secured.
5. Operating Instructions
Power On/Off:
- To power on the display, press and hold the ON/OFF button for a few seconds until the indicators light up.
- To power off, press and hold the ON/OFF button again until the indicators turn off.
- The display will automatically enter sleep mode after 10 minutes of inactivity to conserve battery.
Battery Indicator:
The LED segments labeled "POWER" indicate the current battery charge level. More lit segments mean a higher charge.
Power Assist Levels:
- Press the MODE button to cycle through different power assist levels (e.g., LOW, MED, HIGH).
- The corresponding LED indicators (LOW, MED, HIGH) will illuminate to show the selected assist level.
6km Walk Assist:
Press the 6km button to activate the walk-assist function, which provides a steady low-speed assist for walking alongside your e-bike or scooter.
Fault Indication:
In case of a system malfunction, the display is designed to show a fault indication. Refer to the troubleshooting section or contact support if a fault is indicated.
6. Maintenance
- Cleaning: Wipe the display surface with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Connections: Periodically check all cable connections to ensure they are secure and free from corrosion or damage.
- Storage: When not in use for extended periods, store the display in a dry, cool place away from direct sunlight.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Display does not turn on | Loose cable connection, no power from battery, faulty display. | Check all 5-wire connections. Ensure e-bike/scooter battery is charged and powered on. If problem persists, contact support. |
| No power assist | Incorrect assist level selected, motor/controller issue, fault indicated. | Press MODE button to select a higher assist level. Check for fault indications on the display. Consult your e-bike/scooter manual for motor/controller troubleshooting. |
| Inaccurate battery reading | Battery not fully charged, aging battery, connection issue. | Ensure battery is fully charged. Check battery connections. If the issue persists, the battery may need servicing or replacement. |
| Display shows error code | System malfunction. | Note the error code and refer to your e-bike/scooter controller manual for specific meanings. Contact support with the error code if necessary. |
8. Specifications
- Operating Voltage: 36-48V
- Material Composition: ABS Plastic
- Compatibility: Electric bicycles and electric scooters
- Weight: Approximately 120 Grams
- Dimensions: Small (Compact design)
- Cable: 5-wire connection
9. Warranty and Support
Akozon products are designed for reliability and performance. For specific warranty details, please refer to the purchase documentation or contact your retailer. For technical support or inquiries, please visit the official Akozon store or contact customer service through your point of purchase.
You can visit the Akozon store for more information: Akozon Store