1. Introduction
This manual provides instructions for the proper installation, maintenance, and care of your WORKPRO Replacement Blades (Model W124793AE). These blades are designed specifically for use with the WORKPRO 7.2V Grass Shear and Shrubbery Trimmer (Model W125106AE). Adhering to these guidelines will ensure optimal performance and extend the lifespan of your blades.
2. Safety Information
- Always ensure the main power tool (WORKPRO 7.2V Trimmer) is turned OFF and the battery is removed before attempting to install, remove, or clean the blades.
- Wear appropriate personal protective equipment, including gloves and eye protection, when handling blades.
- Blades are sharp. Handle with extreme care to prevent injury.
- Keep blades out of reach of children.
- Only use genuine WORKPRO replacement blades for your tool. Using non-compatible blades may result in damage to the tool or injury.
3. Setup and Installation
Follow these steps to safely replace the blades on your WORKPRO 7.2V Grass Shear and Shrubbery Trimmer.
- Prepare the Trimmer: Ensure the WORKPRO 7.2V Trimmer (Model W125106AE) is turned off and the battery pack is removed. Place the trimmer on a stable, flat surface.
- Remove Existing Blade: Depending on your trimmer model, there may be a release button or screws securing the blade assembly. Refer to your trimmer's original manual for specific instructions on detaching the worn blade. Carefully remove the old blade, handling it by the non-sharp edges.
- Install New Blade: Align the new WORKPRO Replacement Blade (Model W124793AE) with the mounting mechanism on the trimmer. Ensure all tabs and slots are correctly engaged.
- Secure the Blade: Press firmly or re-engage any locking mechanisms until the blade is securely in place. If screws were removed, reinsert and tighten them appropriately. Gently tug on the blade to confirm it is firmly attached and does not wobble.
4. Operating with New Blades
Once the replacement blades are securely installed, you can resume operation of your WORKPRO 7.2V Grass Shear and Shrubbery Trimmer. Always refer to the main trimmer manual for detailed operating instructions and safety precautions.
- Grass Shear Blade: Ideal for trimming grass around obstacles, edging lawns, and maintaining small areas.
- Shrubbery Trimmer Blade: Suitable for shaping and trimming small hedges, shrubs, and bushes.
5. Maintenance and Storage
Proper maintenance is essential for the longevity and performance of your WORKPRO Replacement Blades.
- Cleaning: After each use, ensure the blades are cleaned thoroughly. Remove any grass clippings, sap, or debris using a stiff brush or cloth. Avoid using harsh chemicals that could damage the blade material.
- Drying: It is crucial to keep the blades dry during storage. Moisture can lead to rust and corrosion, which will dull the blades and reduce their effectiveness. Wipe them dry immediately after cleaning.
- Lubrication: Periodically apply a light coat of machine oil or blade lubricant to the blades to prevent rust and ensure smooth operation.
- Sharpening: Over time, blades will naturally dull. If cutting performance decreases significantly, the blades may need sharpening. This should be done by a qualified professional or with appropriate sharpening tools, following safety guidelines. Alternatively, replace with new WORKPRO blades.
- Storage: Store the blades in a dry, secure location, away from moisture and out of reach of children. If storing separately from the trimmer, use the original packaging or a protective sheath.
6. Troubleshooting
- Blades not cutting effectively:
- Check if blades are dull. Sharpen or replace if necessary.
- Ensure blades are clean and free of debris.
- Verify blades are correctly installed and securely fastened.
- Blades making unusual noise or vibrating:
- Turn off the trimmer and remove the battery. Inspect blades for damage or bending. Replace if damaged.
- Ensure blades are properly seated and tightened.
- Blades do not fit the trimmer:
- Confirm that you have the correct replacement blades (Model W124793AE) for your WORKPRO 7.2V Grass Shear and Shrubbery Trimmer (Model W125106AE).
7. Specifications
- Blade Model: W124793AE
- Compatible Trimmer Model: WORKPRO 7.2V Grass Shear and Shrubbery Trimmer (W125106AE)
- Material: Alloy Steel
- Product Dimensions: Approximately 3.82"L x 0.87"W x 6.69"H (for the blade assembly)
- Item Weight: Approximately 8.1 ounces
- UPC: 820909692881
- Manufacturer: HANGZHOU GREATSTAR INDUSTRIAL CO.,LTD
8. Warranty and Support
For warranty information regarding your WORKPRO Replacement Blades or the WORKPRO 7.2V Grass Shear and Shrubbery Trimmer, please refer to the documentation included with your original trimmer purchase or visit the official WORKPRO website. For technical support or further assistance, please contact WORKPRO customer service through their official channels.
