VIJIM LS23 Broadcast Boom Arm Instruction Manual

Introduction

The VIJIM LS23 Broadcast Boom Arm is a professional-grade desk mount stand designed for content creators, streamers, and broadcasters. It features multiple flexible arms, a laptop tray, and various expansion interfaces, allowing for simultaneous connection of cameras, microphones, and lighting equipment. This manual provides comprehensive instructions for assembly, operation, and maintenance of your LS23 boom arm.

Image: The VIJIM LS23 Broadcast Boom Arm in a typical setup, showcasing its ability to hold a laptop, camera, and lighting simultaneously for a comprehensive live broadcast station.

Safety Information

• Ensure the desk clamp is securely fastened to a stable surface before attaching any equipment.
• Do not exceed the maximum load capacity of 2kg (4.4lb) per arm. The main pole can support up to 10kg (22lb).
• Distribute weight evenly across the arms to maintain stability.
• Keep hands clear of moving parts during adjustment to prevent pinching.
• Avoid placing the stand in high-traffic areas where it could be accidentally knocked over.

Package Contents

Please verify that all components listed below are present in your package.

Image: A visual representation of all components included in the VIJIM LS23 package, such as the desk clamp, extension arms, microphone holder, laptop bracket, and various adapters.

• Desk C-Clamp Mount * 1
• Extension Arm A * 2
• Extension Arm B * 1
• Microphone Holder * 1
• Laptop Bracket * 1
• Laptop Bracket Adapter * 1
• Ballhead * 2
• 1/4" to 3/8" Adapter * 1
• 1/4" to 5/8" Adapter * 1
• Hex Key (for assembly)

Setup and Assembly

1. Attach the C-Clamp Base: Secure the C-clamp mount to the edge of your desk. Ensure the desk thickness is within the 0-90mm clamping range. Tighten the screw until the clamp is firmly in place, protecting the desk surface with the silicone pads.


Image: Detailed view of the C-Clamp Base being attached to a desk, highlighting the anti-slip silicone and the maximum clamping width.

2. Insert the Main Pole: Slide the main pole into the C-clamp base and tighten the securing knob.
3. Attach Extension Arms: Loosen the knobs on the main pole and slide the extension arms into the desired positions. Each arm features a damping knob for fixed-point hovering. Tighten the knobs to secure the arms.


Image: Close-up of the two-section extension arm, showing the damping knob for precise positioning and the pole clamp mechanism.

4. Install Device Mounts:
   • For cameras/lights: Attach the ballheads to the ends of the extension arms. Use the 1/4" screw to mount your camera or light.
   • For microphones: Attach the microphone holder to an arm. Use the appropriate 1/4" to 3/8" or 1/4" to 5/8" adapter if needed.
   • For laptops/tablets: Assemble the laptop bracket with its adapter and attach it to an extension arm.


Image: The VIJIM LS23 boom arm fully assembled with a laptop, camera, and microphone attached, demonstrating its multi-device capability.

Operating Instructions

Angle Adjustment

The VIJIM LS23 offers extensive flexibility for positioning your equipment.

• Arm Rotation: Each extension arm can rotate 360° around the main pole. Loosen the knob on the main pole, adjust the arm, and re-tighten.
• Arm Segment Adjustment: The two-section design of the arms allows for further articulation. Loosen the internal damping knob to adjust the angle and length of each arm segment, then tighten to secure.
• Ballhead Adjustment: The included ballheads provide 360° rotation and tilt for precise camera or light positioning. Loosen the ballhead knob, adjust the device, and tighten firmly.
• Laptop Tray Adjustment: The laptop tray supports 300° rotation and can be adjusted for optimal viewing angles.

Image: Demonstrates the flexible angle adjustment capabilities, including horizontal and vertical camera positioning using the swivel ball head.

Image: Illustrates the various expansion interfaces available, including the universal ballhead, cold shoe, and 1/4", 3/8", and 5/8" interfaces for different accessories.

Maintenance

• Cleaning: Wipe the boom arm with a soft, dry cloth to remove dust and fingerprints. Avoid abrasive cleaners or solvents.
• Inspections: Periodically check all screws and knobs to ensure they are tight. Re-tighten if necessary to maintain stability.
• Storage: When not in use, the boom arm can be collapsed for compact storage. Ensure all attached devices are removed before collapsing.

Troubleshooting

Specifications

Image: Diagram showing key dimensions and load capacities of the VIJIM LS23 Broadcast Boom Arm components.

Warranty and Support

For warranty information, technical support, or any inquiries regarding your VIJIM LS23 Broadcast Boom Arm, please contact VIJIM customer service through their official website or the retailer where the product was purchased. Keep your purchase receipt as proof of purchase.

You can visit the official VIJIM store on Amazon for more information: VIJIM Amazon Store