1. Introduction
This manual provides essential information for the safe and efficient operation of your Eaton UPS 5E Gen2 700 IEC. This Uninterruptible Power Supply (UPS) is designed to protect your electronic devices from power outages and voltage fluctuations, ensuring continuous power and data integrity.
Please read this manual thoroughly before installation and use. Keep it for future reference.
Safety Information
- This UPS is intended for indoor use only.
- Ensure proper ventilation around the unit. Do not block ventilation openings.
- Do not expose the UPS to excessive moisture or extreme temperatures.
- Connect the UPS to a grounded power outlet.
- Do not open the UPS casing. There are no user-serviceable parts inside. Refer all servicing to qualified personnel.
2. Product Overview
The Eaton UPS 5E Gen2 700 IEC is a line-interactive UPS providing reliable power protection for computers, workstations, peripherals, internet routers, NAS devices, TVs, gaming consoles, and other high-energy consumption devices. It features Automatic Voltage Regulation (AVR) to correct voltage fluctuations without using battery power, preserving battery life for actual power outages.
Figure 2.1: Front view of the Eaton UPS 5E Gen2 700 IEC.
Key Features:
- Power Capacity: 700 VA / 360 Watts.
- Battery Runtime: Approximately 14 minutes at standard load.
- Automatic Voltage Regulation (AVR): Corrects undervoltages and overvoltages without switching to battery.
- Auto-Restart Function: The UPS automatically restarts when mains power is restored after a complete battery discharge.
- Silent Operation: Fanless design (up to 1200 VA models) ensures quiet operation.
- Outlets: Equipped with 4 IEC-C13 outlets for connecting protected devices.
Figure 2.2: Side view of the Eaton UPS, showing typical port configuration.
3. Setup
3.1 Unpacking
Carefully unpack the UPS and inspect it for any damage. Retain the packaging for future transport or storage.
3.2 Placement
Place the UPS in a clean, dry, and well-ventilated area. Avoid direct sunlight, heat sources, and excessive dust or humidity. Ensure there is sufficient space around the unit for airflow.
3.3 Connecting to Power
- Connect the UPS power input cable to a grounded wall outlet.
- Connect your computer, monitor, and other critical devices to the IEC-C13 output receptacles on the back of the UPS. Use appropriate IEC cables (not always included).
- Ensure all connections are secure.
3.4 Initial Battery Charge
For optimal performance, charge the UPS battery for at least 8 hours before initial use. The UPS will charge the battery whenever it is connected to mains power, even if it is turned off.
Figure 3.1: The UPS integrated into an office setup.
4. Operating Instructions
4.1 Powering On/Off
- To Power On: Press and hold the power button on the front panel for approximately 2 seconds until the indicator light illuminates.
- To Power Off: Press and hold the power button for approximately 2 seconds until the indicator light turns off.
4.2 LED Indicators
The front panel LED indicator provides status information:
- Solid Green: UPS is operating normally, providing power from the utility.
- Flashing Green: UPS is operating on battery power.
- Solid Red: Indicates a fault or overload condition. Refer to the Troubleshooting section.
4.3 Automatic Voltage Regulation (AVR)
The UPS automatically detects and corrects minor voltage fluctuations (sags or surges) in the utility power without switching to battery mode. This extends battery life and ensures a stable power supply to your connected devices.
4.4 Battery Mode Operation
During a power outage, the UPS will automatically switch to battery power. The LED indicator will flash green, and an audible alarm may sound (if enabled). The UPS will provide power for a limited duration, allowing you to save your work and safely shut down your equipment.
5. Maintenance
5.1 Battery Care
- Keep the UPS connected to mains power to ensure the battery remains charged.
- Avoid frequent deep discharges of the battery, as this can reduce its lifespan.
- Batteries are not user-replaceable. Contact qualified service personnel for battery replacement.
5.2 Cleaning
Clean the exterior of the UPS with a soft, dry cloth. Do not use liquid or aerosol cleaners. Ensure ventilation openings are free from dust and debris.
5.3 Storage
If storing the UPS for an extended period, ensure the battery is fully charged. Store it in a cool, dry place. Recharge the battery every 3-6 months to prevent permanent damage.
6. Troubleshooting
This section addresses common issues you might encounter with your UPS. If the problem persists after following these steps, contact customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| UPS does not turn on | No mains power; Battery discharged; UPS fault | Check power cord and wall outlet; Allow UPS to charge for several hours; Contact support. |
| Short battery runtime | Battery not fully charged; Battery nearing end of life; Overload | Charge UPS for 8+ hours; Reduce connected load; Contact support for battery replacement. |
| Continuous alarm / Red LED | Overload; Internal fault | Disconnect non-essential devices; Power off and restart UPS; If alarm persists, contact support. |
| UPS frequently switches to battery mode | Unstable utility power; High/low voltage outside AVR range | This indicates the UPS is protecting your devices. If frequent, consider checking your building's electrical wiring. |
7. Specifications
| Specification | Value |
|---|---|
| Brand | Eaton |
| Model Number | 5E700I |
| Power Capacity | 700 VA / 360 Watts |
| Input Voltage | 230 Volts (AC) |
| Output Voltage | 700 Volts |
| Frequency Range | 50/60 Hz (± 3 Hz) |
| Number of Outlets | 4 (IEC-C13) |
| Battery Type | Lead-acid |
| Average Battery Runtime | 14 Minutes |
| Product Dimensions (DxWxH) | 28.8P x 10W x 14.8H cm |
| Item Weight | 4.3 Kilograms |
| Color | Black |
| Casing Material | Metal |
| Form Factor | Compact |
| Manufacturer Part Number | 5E700I |
8. Warranty and Support
8.1 Product Warranty
The Eaton UPS 5E Gen2 700 IEC comes with a 2-year manufacturer's warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
8.2 Technical Support
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact your retailer or visit the official Eaton support website. Have your product model number (5E700I) and serial number ready when contacting support.
You can find more information and support resources on the Eaton official website.
