MOUNT PRO B0CBTP6HYC

MOUNT PRO Dual Monitor Stand Instruction Manual

Model: B0CBTP6HYC

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your MOUNT PRO Dual Monitor Stand. Please read these instructions carefully before assembly and use to ensure proper function and safety.

The MOUNT PRO Dual Monitor Stand is designed to securely hold two computer screens ranging from 22 to 42 inches, with a maximum weight capacity of 33 lbs per monitor. It supports VESA mounting patterns of 75x75mm or 100x100mm.

Setup and Installation

The MOUNT PRO Dual Monitor Stand offers two primary installation methods: C-clamp mounting and grommet mounting. Choose the method that best suits your desk type.

1. Check Monitor Compatibility

Ensure your monitors are compatible with the stand's specifications:

Screen Size: 22 to 42 inches
Weight Capacity: Up to 33 lbs per monitor
VESA Patterns: 75x75mm or 100x100mm

For monitors without VESA holes, a VESA adapter (sold separately) may be required.

Diagram showing VESA hole patterns on the back of a monitor and how to remove an original stand. — Figure 1: VESA Compatibility Check. This image illustrates how to identify VESA mounting holes on a monitor and suggests removing the original stand if necessary.

2. Choose Mounting Option

The stand supports two mounting types:

C-Clamp Mounting: Suitable for desk thickness from 0.4" to 1.97". This method requires no drilling.
Grommet Mounting: Suitable for desk thickness from 0.4" to 3.15". Requires a desk hole diameter of 0.4" to 2.4".

Important: Do not install on tempered glass table tops.

Image showing two installation options: C-clamp mounting and grommet mounting, with desk thickness requirements. — Figure 2: Two Installation Options. This image displays the C-clamp method (top) and the grommet method (bottom) for attaching the monitor stand to a desk, along with their respective desk thickness and hole diameter specifications.

Diagram illustrating compatible and incompatible desk types for C-clamp mounting, including warnings against tempered glass. — Figure 3: Desk Compatibility for C-Clamp. This diagram shows various desk edge configurations, indicating which are suitable for C-clamp mounting and explicitly warns against using the mount on tempered glass surfaces.

3. Attaching Monitors

The VESA plate is detachable for easy assembly. Attach the VESA plate to the back of your monitor using the provided screws, then slide the monitor onto the arm head until it locks securely.

Image showing a person attaching a monitor to the stand, highlighting the detachable VESA plate for easy assembly. — Figure 4: Effortless Assembly. This image demonstrates the process of attaching a monitor to the stand using the detachable VESA plate, emphasizing the ease of installation.

Diagram showing how to easily lock the monitor onto the arm head without additional operations. — Figure 5: Easy Monitor Locking. This diagram illustrates how the monitor slides onto the arm head and automatically locks into place, simplifying the attachment process.

Operating and Adjustments

The MOUNT PRO Dual Monitor Stand features gas spring arms for flexible and ergonomic adjustments.

1. Flexible Screen Adjustment

Adjust your monitors to achieve optimal viewing angles and ergonomic positions. The arms allow for:

Tilt: +90° to -45°
Swivel: 180°
Rotation: 360° (for landscape or portrait viewing)
Max Extension: Up to 23.58 inches
Max Height: Up to 19.69 inches

Diagram illustrating the flexible screen adjustment capabilities: swivel, tilt, and rotation, along with maximum height and extension. — Figure 6: Flexible Screen Adjustment. This diagram shows the range of motion for swivel (180°), tilt (+90°/-45°), and rotation (360°), as well as the maximum extension (23.58") and height (19.69") of the monitor arms.

Image showing various screen combinations and orientations possible with the dual monitor stand. — Figure 7: Multiple Screen Combinations. This image illustrates different display configurations possible with the dual monitor stand, including side-by-side, stacked, and angled setups.

2. Tilt and Tension Adjustment

To adjust the tilt and gas spring tension:

Tilt Adjustment: Loosen the tilting bolt (turn in "+" direction), adjust your monitor to the desired tilt angle, then retighten the tilting bolt (turn in "-" direction).
Tension Adjustment: Keep the arm in a horizontal position during adjustment.
- If the monitor raises up, turn clockwise ("-" direction) to reduce tension for lighter monitors.
- If the monitor falls down, turn counter-clockwise ("+" direction) to increase tension for heavier monitors.

Diagram showing how to adjust tilt and gas spring tension for the monitor arm. — Figure 8: Tilt and Tension Adjustment. This diagram illustrates the steps for adjusting the monitor's tilt and the gas spring tension to accommodate different monitor weights and desired positions.

Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your monitor stand.

1. Cable Management

Utilize the integrated cable management system to keep your workspace tidy and prevent cable damage. Route cables along the arms and through the designated channels.

Image showing the integrated cable management system on the monitor arm, with cables routed neatly. — Figure 9: Cable Management. This image highlights the hidden cable design, demonstrating how cables can be routed through the monitor arm for a clean and organized desktop.

2. Cleaning

Wipe the stand with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the finish.

Troubleshooting

This section addresses common issues you might encounter with your monitor stand.

Monitor Sags or Does Not Stay in Position: This indicates that the gas spring tension needs adjustment. Refer to the "Tension Adjustment" instructions in the Operating section. Ensure the arm is held horizontally during adjustment.
Monitor is Difficult to Move: The gas spring tension might be too high. Refer to the "Tension Adjustment" instructions to reduce tension.
Monitor Does Not Tilt: Ensure the tilting bolt is sufficiently loosened before attempting to adjust the tilt. Retighten after achieving the desired angle.
Stand is Unstable: Verify that the C-clamp or grommet mount is securely tightened to the desk. Check desk compatibility to ensure it meets the thickness and material requirements.
Cables are Disorganized: Utilize the integrated cable management channels along the arms to route and secure your cables.

Specifications

Feature	Detail
Brand	MOUNT PRO
Model	B0CBTP6HYC
Monitor Size Compatibility	22" to 42" (Ultrawide)
Weight Capacity	6.6 lbs to 33 lbs per monitor
VESA Compatibility	75x75mm, 100x100mm
Mounting Type	Tabletop Mount (C-Clamp or Grommet)
Movement Type	Rotate, Swivel, Tilt, Articulating
Tilt Range	+90° to -45°
Swivel Range	180°
Rotation Range	360°
Max Extension	23.58 inches
Max Height	19.69 inches
Material	Metal (Aluminum)
Color	Black
Item Weight	14.52 pounds

Image showing the MOUNT PRO Dual Monitor Stand supporting two large ultrawide monitors, emphasizing its heavy-duty design. — Figure 11: Design for Heavier Monitors. This image illustrates the stand's capability to support two large monitors, up to 42 inches and 33 lbs each, with VESA compatibility of 75x75mm or 100x100mm.

Diagram showing the recommended distance between the screen and wall for various monitor sizes when using the stand. — Figure 12: Screen to Wall Distance Guide. This diagram provides a table of recommended distances from the screen to the wall for different monitor sizes (15" to 42") to ensure proper clearance and movement.

Warranty Information

Specific warranty details are not provided in the product information. Please refer to the product packaging or contact MOUNT PRO customer support for warranty terms and conditions.

Customer Support

For technical assistance, missing parts, or any inquiries regarding your MOUNT PRO Dual Monitor Stand, please contact MOUNT PRO customer support through their official website or the retailer where the product was purchased.

Product Videos

Extra Wide Monitor Stand Overview

This video provides a demonstration of the MOUNT PRO Dual Monitor Stand, showcasing its ability to hold an extra-wide monitor and highlighting its adjustable features and cable management capabilities. The video illustrates the stability and flexibility of the stand for large displays.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.