1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Memphis Audio SRXP62CV2 SRX Pro 6.5-inch Component Car Speakers with LED. Please read this manual thoroughly before attempting installation or operation to ensure proper function and safety. Retain this manual for future reference.
The SRXP62CV2 component set is designed to deliver high-output audio performance with the added visual appeal of RGB LED illuminated dust caps.
Image 1: Complete Memphis Audio SRXP62CV2 Component Speaker Set.
2. Safety Information
Always observe the following safety precautions during installation and operation:
- Disconnect the vehicle's negative battery terminal before beginning any electrical work to prevent short circuits.
- Ensure all wiring is properly insulated to prevent shorts and electrical hazards.
- Mount speakers securely to prevent them from becoming projectiles in the event of a sudden stop or collision.
- Avoid installing speakers in locations that obstruct vehicle operation or safety features.
- Do not operate audio systems at excessively high volumes for prolonged periods, as this can cause hearing damage.
- Consult a professional installer if you are unsure about any part of the installation process.
3. Package Contents
Verify that all items are present in the package:
- Two (2) 6.5-inch Woofers with RGB LED Illuminated Dust Caps
- Two (2) Tweeters
- Two (2) Passive Crossovers
- Two (2) Speaker Grills
- Mounting Hardware (screws, clips)
- Wiring Harnesses for LED (as shown in image)
- Instruction Manual (this document)
4. Setup & Installation
Proper installation is crucial for optimal performance and safety. If you are not comfortable with car audio installation, seek professional assistance.
4.1. Mounting
The SRXP62CV2 component set includes mounting templates to assist with installation. Ensure the chosen mounting location provides adequate depth and clearance for the speakers and tweeters.
Image 2: Mounting Templates and Wiring Harnesses.
- Woofer Mounting: Use the provided template (Part Number A: SRXP62CV2) to mark the mounting holes and cut-out diameter (5.61" / 142mm) for the 6.5-inch woofers. Ensure a mounting depth of 2.85 inches is available.
- Tweeter Mounting: Use the provided template (Part Number B: SRXP62CV2) for the tweeters. The mounting hole is 2.04" / 52mm.
- Securely fasten all components using the supplied screws.
4.2. Wiring
The SRXP62CV2 is a component set, requiring connection of woofers and tweeters to the passive crossovers, and then the crossovers to your amplifier.
Image 3: Woofer Terminal Connections.
- Crossover Connections: Connect the amplifier's output to the 'INPUT' terminals on the passive crossover. Connect the woofer to the 'WOOFER' terminals and the tweeter to the 'TWEETER' terminals on the crossover. Observe correct polarity (+ to + and - to -).
- Speaker Wiring: Use appropriate gauge speaker wire for all connections. Ensure all connections are tight and free from corrosion.
- LED Wiring: The speakers feature RGB LED illuminated dust caps. Connect the provided LED wiring harnesses to a suitable 12V power source in your vehicle. An RGB controller (sold separately) may be required for color control. Refer to the LED controller's manual for specific wiring instructions.
- Amplifier Connection: Connect the passive crossovers to your amplifier's speaker outputs. Ensure the amplifier is capable of handling the speaker's power requirements (125W RMS per channel).
5. Operation
Once installed, the SRXP62CV2 speakers will reproduce audio signals from your amplifier. Proper amplifier setup is essential for optimal sound quality and speaker longevity.
- Amplifier Gain Setting: Set your amplifier's gain control carefully. Start with the gain at its minimum setting and slowly increase it until the desired volume is achieved without distortion. Refer to your amplifier's manual for detailed gain setting procedures.
- Crossover Settings: The passive crossovers included with the SRXP62CV2 are designed to properly distribute frequencies to the woofer and tweeter. No external crossover adjustments are typically needed for the speakers themselves.
- LED Control: If an RGB controller is installed, use it to select the desired LED color and effects.
Image 4: SRX Pro Woofers with Blue LED Illumination.
6. Maintenance
The Memphis Audio SRXP62CV2 speakers require minimal maintenance.
- Keep the speaker cones and surrounds free from dust and debris. Use a soft, dry cloth for cleaning.
- Avoid exposing speakers to excessive moisture or direct sunlight for prolonged periods.
- Periodically check all wiring connections to ensure they remain secure.
7. Troubleshooting
If you experience issues with your SRXP62CV2 speakers, refer to the table below for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from speakers | Loose wiring connection Amplifier not powered on Incorrect crossover wiring | Check all speaker and amplifier connections Verify amplifier power and fuse Ensure woofer/tweeter are connected to correct crossover terminals |
| Distorted sound | Amplifier gain set too high Damaged speaker wire Speaker damaged | Reduce amplifier gain Inspect and replace damaged wiring Contact Memphis Audio support if speaker is damaged |
| LEDs not illuminating | LED wiring disconnected No 12V power to LED circuit Faulty LED controller | Check LED wiring connections Verify 12V power source Test or replace LED controller |
| One speaker not working | Loose connection to that speaker/crossover Faulty speaker/crossover | Check all connections for the affected speaker Swap components (if possible) to isolate the fault; contact support |
8. Specifications
| Feature | Specification |
|---|---|
| Model | SRXP62CV2 |
| Speaker Size | 6.5 Inches |
| RMS Power (W) | 125W per speaker |
| Peak Power (W) | 250W per speaker |
| Sensitivity (dB) | 94 dB |
| Impedance | 4 Ohm |
| Mounting Depth | 2.85 Inches |
| Magnet Size | 22 OZ |
| Woofer Cone Material | Ultra-light treated paper |
| Surround Material | Cloth treated |
| Voice Coil | 1.5" VC |
| Special Feature | RGB LED Illuminated Dust Cap |
| Included Components | Grill |
| Product Dimensions | 15.12"D x 11.77"W x 3.66"H (Package) |
| Item Weight | 11.15 pounds |
9. Warranty & Support
Memphis Audio products are manufactured with quality in mind. The SRXP62CV2 speakers come with a Limited Warranty. Please refer to the warranty information provided with your product or visit the official Memphis Audio website for full details regarding warranty terms, conditions, and claim procedures.
For technical support or service inquiries, please contact Memphis Audio customer service through their official website or authorized dealers. Ensure you have your product model number (SRXP62CV2) and proof of purchase available when seeking support.
