Bellemave Twin Over Twin House Bunk Bed with Storage Stairs and Slide Instruction Manual

Introduction

This manual provides detailed instructions for the assembly, operation, and maintenance of your Bellemave Twin Over Twin House Bunk Bed. Please read all instructions carefully before assembly and use to ensure safe and proper operation.

Important Safety Information

• WARNING: Bunk beds can present a serious hazard. Follow all assembly instructions and safety guidelines.
• Always use the recommended mattress size for both upper and lower bunks. Upper bunk: 6 inches thick. Lower bunk: 8-10 inches thick. Trundle: 6 inches thick.
• Ensure all connections are tight before use and check periodically.
• The upper bunk is not suitable for children under 6 years of age.
• Do not allow more than one person on the upper bunk.
• Always use the provided guardrails on the upper bunk.
• Do not attach or hang items on any part of the bunk bed that are not designed for use with the bed.
• Keep children away from the assembly area until assembly is complete.
• Maximum weight capability for upper bed, lower bed, and trundle is 300 lbs each.

Parts List

Before beginning assembly, ensure all parts are present and undamaged. Refer to the included hardware pack for specific component identification.

• Pine wood and MDF frame components
• Bed slats (14 for upper, 14 for lower, 7 for trundle)
• Guardrails for upper bunk
• Storage staircase with drawers
• Slide component
• Trundle bed frame
• Roof and window panels
• Assembly hardware (bolts, screws, etc.)

Setup and Assembly Instructions

Assembly requires two adults and approximately one hour. Follow these steps carefully. Do not overtighten bolts until instructed.

1. Unpack Components: Carefully unpack all boxes and lay out components on a soft, clean surface to prevent scratching. Verify all parts against the parts list.
2. Assemble Bed Frames: Begin by assembling the main twin bed frames for both the upper and lower bunks. Attach side rails to headboards and footboards using the provided hardware.
3. Install Bed Slats: Securely attach the bed slats to both the upper and lower bed frames. Ensure even spacing and firm attachment for mattress support.
4. Construct Storage Staircase: Assemble the storage staircase unit. Install the drawers into their respective compartments.
5. Attach Staircase and Slide: Connect the assembled staircase to the main bunk bed frame. Attach the slide to the designated opening on the upper bunk.
6. Assemble Trundle Bed: Assemble the trundle bed frame. This unit is designed to roll out from under the lower bunk.
7. Install Roof and Window Panels: Attach the pitched roof and window panels to the upper bunk structure to complete the playhouse design.
8. Final Tightening: Once all components are in place and aligned, securely tighten all bolts and screws. Do not overtighten to avoid damaging the wood.
9. Safety Check: Before use, ensure all connections are secure, guardrails are properly installed, and the bed is stable.

Image: Fully assembled Bellemave Twin Over Twin House Bunk Bed in gray, featuring the roof, window, slide, storage stairs, and trundle bed pulled out.

Image: Detailed diagram showing the dimensions of the Bellemave Twin Over Twin House Bunk Bed, including length, width, and height of various components like the bed frames, slide, and stairs.

Operating Instructions

• Using the Bunk Beds: Ensure mattresses are correctly placed on the slats. The upper bunk is accessed via the storage staircase.
• Using the Slide: The slide is intended for supervised play. Ensure the area around the slide exit is clear before use.
• Using the Trundle Bed: The trundle bed can be pulled out from under the lower bunk for an additional sleeping space. Push it back in when not in use to save space.
• Using Storage Stairs: The drawers within the staircase provide convenient storage for toys or bedding.

Maintenance

• Cleaning: Wipe the bed frame with a dry cloth. Avoid harsh chemicals or abrasive cleaners.
• Hardware Check: Periodically check all bolts and screws to ensure they remain tight. Retighten as necessary.
• Structural Integrity: Inspect the bed frame regularly for any signs of wear, damage, or loose components. Discontinue use if damage is found until repairs are made.

Troubleshooting

Issue: Bed feels wobbly after assembly.

Solution: Ensure all bolts and screws are fully tightened. Check that all components are correctly aligned according to the assembly instructions. Disassemble and reassemble if necessary, ensuring not to overtighten until all parts are in place.

Issue: Trundle bed does not slide smoothly.

Solution: Check the wheels of the trundle bed for any obstructions or debris. Ensure the floor surface is clear. Lubricate wheel axles if needed with a suitable furniture lubricant.

Issue: Missing parts.

Solution: Refer to the parts list and contact Bellemave customer support with the specific part numbers required.

Specifications

Customer Support

For any questions, missing parts, or assistance with assembly, please contact Bellemave customer support. Refer to your purchase documentation for contact details or visit the official Bellemave website.