G-Mac Axis Evo 2.0 Modular Motorcycle Helmet

Introduction

Thank you for choosing the G-Mac Axis Evo 2.0 Modular Motorcycle Helmet. This helmet is designed to provide optimal protection and comfort for motorcyclists, featuring a versatile modular design and dual visors. It is ECE 22.06 approved and P&J certified, ensuring high safety standards. Please read this manual thoroughly before using your helmet to ensure proper fit, operation, and maintenance.

Image: The G-Mac Axis Evo 2.0 Modular Helmet in Gloss White, showcasing its sleek design and integrated visors.

Product Features

• Latest ECE 22.06 Standard compliant: Meets the most recent European safety standards for motorcycle helmets.
• P&J Certified: Dual homologation for both 'P' (protective) and 'J' (jet/open face) configurations, allowing safe riding with the chin bar up or down.
• MPT (Multi-Poly Tech) Shell Construction: Durable and lightweight shell for enhanced protection.
• Integrated Pivoting Chin-Bar Modular Design: Allows the chin bar to be easily lifted and locked into an open position.
• Integrated Inner Sun Visor: Provides convenient sun protection without needing to change the main clear visor.

Setup and Fitting

1. Initial Inspection

Before first use, carefully inspect your helmet for any signs of damage from shipping. Ensure all components are securely attached and function correctly.

2. Sizing and Fit

A properly fitting helmet is crucial for safety. Refer to the size guide below to ensure your helmet fits snugly and comfortably without pressure points.

Image: The G-Mac Axis Evo 2.0 Modular Helmet with its chin bar in the raised position, demonstrating its modular functionality.

3. Visor Installation/Adjustment

The main clear visor and inner sun visor come pre-installed. For removal or adjustment, refer to the specific instructions provided in the included leaflet or on the G-Mac official website. Ensure both visors operate smoothly and lock securely in place.

Operating the Helmet

1. Modular Flip-Up Mechanism

To raise the chin bar, locate the release button/lever, typically positioned at the center front of the chin bar. Press the button and pivot the chin bar upwards until it locks securely in the open position. To close, press the release button again and pivot the chin bar downwards until it clicks firmly into place. Always ensure the chin bar is fully locked before riding.

Image: Side view of the G-Mac Axis Evo 2.0 helmet demonstrating the chin bar in its fully raised position.

2. Integrated Inner Sun Visor

The inner sun visor is operated by a slider mechanism, usually located on the left side of the helmet shell. Slide the lever forward to deploy the sun visor and backward to retract it. Use the sun visor only in bright conditions and retract it immediately when light conditions change or visibility is reduced.

Image: The G-Mac Axis Evo 2.0 Modular Helmet with both the chin bar raised and the inner sun visor deployed.

3. Ventilation System

The helmet features adjustable vents for airflow. Locate the top and chin vents and slide them open or closed to control ventilation. Ensure vents are clear of obstructions for optimal performance.

4. Chin Strap (Ratchet Closure)

To fasten the chin strap, insert the male end of the ratchet into the female buckle until it clicks securely. Adjust the strap length for a snug fit under your chin. To release, pull the red tab on the female buckle. Always ensure the chin strap is securely fastened before riding.

Image: A close-up view of the helmet's ratchet closure system for the chin strap, highlighting its secure fastening mechanism.

Maintenance

1. Cleaning the Helmet Shell

Clean the helmet shell with a soft, damp cloth and mild soap. Avoid abrasive cleaners, solvents, or petroleum-based products, as these can damage the shell material and finish. Rinse thoroughly and dry with a soft, clean cloth.

2. Cleaning the Visors

Remove the main clear visor and inner sun visor before cleaning. Use only warm water and a soft microfiber cloth. For stubborn dirt, a very mild soap solution can be used. Rinse thoroughly and air dry. Do not use chemical cleaners or abrasive materials, as they can scratch or damage the visor coatings.

Image: A detailed view of the helmet's clear main visor, showing its optical clarity.

3. Liner Removal and Cleaning

The helmet's interior comfort liner is removable for cleaning. Gently detach the liner components (cheek pads, crown liner) according to the instructions in the included leaflet. Hand wash with mild soap and cool water, then air dry completely before re-installing. Ensure all components are dry to prevent mildew.

4. Storage

Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Use the provided helmet bag to protect it from dust and scratches. Do not store the helmet near chemicals or solvents.

Troubleshooting

• Visor Fogging: Ensure proper ventilation by opening vents. Consider using an anti-fog insert (Pinlock compatible, if applicable) or anti-fog spray.
• Loose Fit: If the helmet feels loose after initial use, re-check your head circumference against the size guide. Ensure the chin strap is adjusted snugly. If still loose, the helmet size may be incorrect.
• Stiff Modular Mechanism: Apply a small amount of silicone spray to the pivot points of the chin bar mechanism if it becomes stiff. Avoid oil-based lubricants.
• Visor Scratches: Always handle visors with care. Clean only with soft cloths and appropriate cleaners. Store the helmet in its bag to prevent scratches. Replacement visors are available from authorized dealers.

Specifications

Warranty and Support

Warranty information for your G-Mac Axis Evo 2.0 helmet is typically provided with your purchase documentation or can be found on the official G-Mac website. Please retain your proof of purchase for any warranty claims.

For technical support, spare parts, or further assistance, please contact your authorized G-Mac dealer or visit the G-Mac official website for contact information.

You can visit the G-Mac store online: G-Mac Store