Introduction
This manual provides essential information for the installation, operation, and maintenance of your new HATARI Refrigerator Ice Maker. This aftermarket replacement part is designed for compatibility with various refrigerator brands including Kenmore, Whirlpool, KitchenAid, Maytag, and Amana, specifically replacing models #S 106 626661 and W106 626661. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Safety Information
Always prioritize safety when working with electrical appliances. Failure to follow these safety instructions could result in electric shock, fire, or personal injury.
- Disconnect Power: Always unplug the refrigerator from the power outlet before attempting any installation, maintenance, or repair.
- Qualified Personnel: If you are unsure about any step, it is recommended to seek assistance from a qualified appliance technician.
- Wear Protective Gear: Use gloves and eye protection when handling tools and components.
- Water Supply: Ensure the water supply to the refrigerator is turned off before disconnecting or connecting any water lines.
- Inspect Components: Before installation, carefully inspect all components for any damage. Do not install damaged parts.
Package Contents
Verify that all items are present in the package:
- 1x Refrigerator Ice Maker Assembly
- Note: Additional components such as wiring harnesses may or may not be included depending on the specific product variant. Please refer to the product images and description at the time of purchase.
Image 1: The complete HATARI Refrigerator Ice Maker Assembly, showing the main body, ice mold, and wire bail arm.
Setup and Installation
This section provides general guidance for installing the ice maker. Specific steps may vary depending on your refrigerator model. Always consult your refrigerator's service manual for detailed instructions.
- Prepare the Refrigerator:
- Unplug the refrigerator from the electrical outlet.
- Turn off the water supply valve to the refrigerator.
- Remove the ice bucket and any shelves or covers that obstruct access to the ice maker compartment.
- Remove the Old Ice Maker:
- Locate the mounting screws or clips holding the old ice maker in place. Remove them.
- Carefully disconnect the electrical wiring harness from the old ice maker. Note the orientation of the connector.
- Disconnect any water lines if they are directly attached to the ice maker.
- Remove the old ice maker from the freezer compartment.
Image 2: Side view of the ice maker, illustrating the internal ice mold and the wire bail arm in the down position.
- Install the New Ice Maker:
- Align the new HATARI ice maker with the mounting points in the freezer compartment.
- Secure the ice maker using the appropriate screws or clips. Ensure it is firmly in place.
- Connect the electrical wiring harness to the new ice maker. Ensure the connection is secure and correctly oriented.
- If applicable, reconnect any water lines.
Image 3: Top view of the ice maker, highlighting the electrical wiring harness connection point.
- Final Steps:
- Replace any removed shelves or covers.
- Turn on the water supply valve to the refrigerator.
- Plug the refrigerator back into the electrical outlet.
- Allow several hours for the ice maker to begin producing ice. The first few batches of ice may be smaller or irregular.
Operating Instructions
Once installed and powered, the ice maker operates automatically. It will fill with water, freeze the water into cubes, and then eject the cubes into the ice bucket.
- Ice Production: The ice maker will cycle automatically as ice is used or melts.
- Wire Bail Arm: The metal wire bail arm controls ice production.
- When the arm is in the down position, the ice maker will produce ice.
- When the arm is in the up position (resting against the top of the ice maker), ice production will stop. This is typically used when the ice bucket is full or if you wish to temporarily stop ice production.
- Initial Ice: Discard the first few batches of ice to ensure any manufacturing residues are flushed out.
Maintenance
Regular maintenance helps ensure optimal performance and longevity of your ice maker.
- Cleaning the Ice Bucket: Periodically remove and wash the ice bucket with mild soap and warm water. Rinse thoroughly and dry completely before returning it to the freezer.
- Cleaning the Ice Maker: If mineral deposits or debris accumulate on the ice maker components, you can gently wipe them with a damp cloth. Do not use abrasive cleaners or harsh chemicals. Ensure the refrigerator is unplugged before cleaning.
- Water Filter: If your refrigerator has a water filter, ensure it is replaced regularly according to the refrigerator manufacturer's recommendations to maintain water quality and prevent mineral buildup in the ice maker.
Troubleshooting
If your ice maker is not functioning as expected, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Ice maker not producing ice. |
|
|
| Small or hollow ice cubes. |
|
|
| Ice cubes stuck in mold. |
|
|
If the problem persists after attempting these solutions, please contact customer support or a qualified technician.
Specifications
| Feature | Detail |
|---|---|
| Brand | HATARI |
| Model Number | W106 |
| Model Name | refrigerator ice maker |
| Product Dimensions | 12.6 x 6.73 x 6.26 inches |
| Compatible Models | #S 106 626661, W106 626661 (Aftermarket replacement for Kenmore, Whirlpool, KitchenAid, Maytag, Amana) |
| UPC | 734665738670 |
Warranty Information
Specific warranty details for this HATARI Refrigerator Ice Maker are not provided in this manual. For information regarding warranty coverage, terms, and conditions, please refer to the product packaging, the seller's website, or contact the manufacturer directly.
Customer Support
If you encounter any issues or have questions that are not addressed in this manual, please contact the seller or manufacturer for assistance. When contacting support, please have your product model number (W106) and purchase details ready.
Note: If you are not sure about the compatibility of this part with your specific refrigerator model, please contact the seller for advice. They aim to resolve your problem within 24 hours.
