Introduction
Thank you for purchasing the WallarGe Atomic Wall Clock. This manual provides detailed instructions for setting up, operating, and maintaining your new clock. Please read this manual thoroughly before use to ensure proper function and longevity of your product.
Image: The WallarGe Atomic Wall Clock displaying its night light feature, with illuminated numbers against a dark background.
Key Features
- Atomic Time Synchronization: Automatically sets and updates time via WWVB radio signal.
- Smart Night Light: Integrated light sensor automatically illuminates the clock face in low light conditions with adjustable brightness (Off/Low/High).
- Silent Movement: Non-ticking quartz movement ensures a quiet environment.
- Battery Operated: Cordless design for flexible placement.
- Auto DST: Automatic adjustment for Daylight Saving Time.
- Large Display: 12-inch diameter with clear, bold numbers for easy readability.
Setup Guide
1. Battery Installation
- Locate the battery compartments on the back of the clock.
- Insert one (1) AA battery into the compartment for the clock movement, observing the correct polarity (+/-).
- Insert three (3) AA batteries into the compartment for the smart light sensor, observing the correct polarity (+/-).
- Replace the battery covers securely.
Image: Rear view of the clock illustrating the battery placement for both the clock movement and the smart light sensor, along with the 12-inch dimensions.
Note: Batteries are not included with the product. Use fresh alkaline batteries for optimal performance.
2. Initial Time Synchronization (Atomic Signal)
After battery installation, the clock will automatically attempt to receive the WWVB atomic time signal from Fort Collins, Colorado. This process may take several minutes to several hours, depending on your location and environmental conditions.
- The clock hands will typically move to the 12:00 position and then begin searching for the signal.
- Once the signal is received, the clock will automatically set itself to the correct time for the selected time zone.
Image: Diagram showing the atomic wall clock on a wall, with concentric circles representing the WWVB signal being received for automatic time updates.
3. Setting Time Zone and DST
On the back of the clock, locate the time zone selection switch and the DST (Daylight Saving Time) switch.
- Time Zone: Select your desired time zone (PST, MST, CST, EST) using the switch.
- DST: Set the DST switch to "ON" for automatic Daylight Saving Time adjustments, or "OFF" if your region does not observe DST.
4. Adjusting Night Light Brightness
The smart night light has three brightness levels. On the back of the clock, locate the brightness adjustment button.
- Press the button to cycle through the settings: Off, Low Brightness, High Brightness.
- Select the desired brightness level for the night light feature.
Image: A visual comparison of the clock's night light feature, demonstrating the 'Off', 'Low Brightness', and 'High Brightness' settings in a dark environment.
Operating Instructions
Automatic Timekeeping
Once set up, the WallarGe Atomic Wall Clock will automatically receive the WWVB signal daily, typically overnight, to ensure accurate timekeeping. No manual adjustments are required under normal operation.
Smart Night Light Function
The integrated light sensor detects ambient light levels. When the room darkens, the night light will automatically activate at the previously selected brightness level (Low or High). When the room brightens, the night light will turn off to conserve battery power.
Silent Operation
The clock features an upgraded precise quartz movement that ensures a completely silent, non-ticking operation. This makes it suitable for environments where quiet is preferred, such as bedrooms, offices, and classrooms.
Image: The clock displayed in a dimly lit room, emphasizing its silent sweep second hand and the soft glow of its night light feature.
Maintenance
Battery Replacement
When the clock hands stop moving or the night light dims significantly, it is time to replace the batteries. Follow the battery installation steps in the Setup Guide. Always replace all batteries at once with new ones of the same type.
Cleaning
To clean the clock, gently wipe the surface with a soft, dry cloth. Do not use abrasive cleaners, solvents, or chemical sprays, as these may damage the clock's finish or internal components.
Environmental Considerations
Avoid placing the clock in direct sunlight, near strong magnetic fields, or in areas with extreme temperatures or high humidity, as these conditions can affect accuracy and lifespan.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Clock does not set time automatically. |
|
|
| Night light is not working. |
|
|
| Clock hands are stuck or moving erratically. |
|
|
Specifications
| Feature | Detail |
|---|---|
| Brand | WallarGe |
| Model Number | CL-508 |
| Display Type | Analog |
| Special Feature | Atomic Wall Clock, Smart Night Light, Silent Movement, Auto DST |
| Product Dimensions | 12"W x 12"H |
| Power Source | Battery Powered (1x AA for movement, 3x AA for light sensor) |
| Material | Acrylonitrile Butadiene Styrene (ABS) |
| Color | Black |
| Mounting Type | Wall Mount |
| Item Weight | 2.49 pounds |
Warranty and Support
Specific warranty details are not provided within this manual. For information regarding warranty coverage, please refer to the product packaging or contact WallarGe customer support directly.
If you encounter any issues not covered in the troubleshooting section, or require further assistance, please visit the official WallarGe website or contact their customer service department.
WallarGe Store Link: Visit the WallarGe Store on Amazon
