1. Product Overview
The LINGXIAO 3/4HP Pool Booster Pump is designed to provide optimal suction power for pressure pool cleaners. This Energy Star 3.1 standard pump is compatible with various OEM models, including #PB4-60 Booster Pump, #PB460, #W36060, and #EC-LA01N, LA_MS05. It features an LX Energy Efficiency Motor, suitable for outdoor use, offering stable flow and low noise operation.
Key features include:
- Dual Voltage Compatibility: Operates on either 230V or 115V (factory default is 230V, manual wiring change required for 115V).
- TEFC Motor: Totally Enclosed Fan Cooled motor for outdoor durability against rain and sun.
- Pre-tested: Each pump is tested for 30 minutes before leaving the factory to ensure quality.
- Quick Connect Kit: Includes a 6.5ft soft tube and 4 connect fittings for easy installation.
2. Package Contents
Upon opening the package, please verify that all components are present:
- 1 x LINGXIAO Relaax 204-ES Pool Booster Pump
- 1 x User Manual (this document)
- 1 x 6.5ft Soft Tube
- 4 x Connect Fittings (various sizes)
Note: A small amount of residual water may be present in the pump due to factory testing. This is normal and indicates a brand new unit.
3. Setup and Installation
3.1. Site Selection
Choose a dry, level location near your pool equipment, protected from direct weather exposure if possible, although the TEFC motor is designed for outdoor use. Ensure adequate ventilation around the pump.
3.2. Electrical Wiring (Important!)
The factory default operating voltage for this pump is 230V. If your electrical supply is 115V, you MUST manually change the wiring configuration inside the pump's terminal box before operation. Failure to do so may result in damage to the pump or electrical system.
Refer to the detailed wiring diagram below for correct connections for both 230V and 115V setups. Always ensure power is disconnected at the circuit breaker before performing any wiring.
3.3. Plumbing Connections
Connect the pump to your existing pool plumbing using the provided quick connect fittings and soft tube. Ensure all connections are secure and watertight to prevent leaks. The pump is designed for easy integration with standard pool cleaner systems.
4. Operating Instructions
Once properly installed and wired, the LINGXIAO Pool Booster Pump is ready for operation. This pump is specifically designed to enhance the performance of pressure-side pool cleaners by providing consistent and powerful water flow.
4.1. Initial Start-up
- Ensure all plumbing connections are tight and the pump is filled with water (primed) if necessary, to prevent dry running.
- Restore power to the pump at the circuit breaker.
- The pump should start operating, providing boosted pressure to your pool cleaner.
4.2. Performance Characteristics
The LX Energy Efficiency Motor ensures stable flow and low noise operation, contributing to a quieter pool environment. Its design is optimized for pressure pool cleaners, delivering the necessary power for effective cleaning.
The pump supports both 230V and 115V electrical systems, offering flexibility for various installations. Its high compatibility allows it to work seamlessly with popular pool cleaner brands.
5. Maintenance
Regular maintenance ensures the longevity and efficient operation of your LINGXIAO Pool Booster Pump. Always disconnect power before performing any maintenance.
5.1. Routine Checks
- Inspect for Leaks: Periodically check all plumbing connections for any signs of water leaks. Tighten fittings as needed.
- Clean Debris: Ensure the area around the pump is free from leaves, dirt, and other debris that could obstruct airflow to the motor or interfere with plumbing.
- Listen for Unusual Noises: While the pump is designed for low noise, any new or unusual sounds could indicate a problem.
5.2. Winterization (if applicable)
In regions subject to freezing temperatures, it is crucial to properly winterize your pump to prevent damage. Consult a pool professional for specific winterization procedures for your pool system.
6. Troubleshooting
This section provides solutions to common issues you might encounter with your LINGXIAO Pool Booster Pump. For problems not listed here, please contact customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not start | No power supply | Check circuit breaker, ensure pump is plugged in. |
| Pump runs but no water flow / low flow | Pump not primed; Air leak in suction line; Clogged impeller | Prime the pump; Check and tighten all suction side connections; Inspect and clear impeller. |
| Unusual noise from pump | Air in system; Worn bearings; Debris in pump | Bleed air from system; Contact support for bearing issues; Inspect and clear pump of debris. |
| Water leaking from pump | Loose connections; Damaged seal | Tighten all plumbing connections; Inspect and replace seals if damaged. |
7. Specifications
Detailed technical specifications for the LINGXIAO Relaax204-ES Pool Booster Pump:
| Specification | Value |
|---|---|
| Brand | LINGXIAO |
| Model Number | Relaax204-ES |
| Power Source | AC |
| Voltage | 230 Volts (AC) or 115 Volts (AC) with manual wiring change |
| Wattage | 750 watts |
| Item Weight | 24 Pounds |
| Product Dimensions (L x W x H) | 15.98" x 6.89" x 8.78" |
| Maximum Flow Rate | 528 Cubic Meters Per Hour |
| Maximum Lifting Height | 131.23 Feet |
| Sound Level | 35 dB |
| Material | Metal |
| Color | Black |
| Hose Length (Included) | 79 Inches (approx. 6.5 ft) |
| Specific Uses For Product | InGround Pool |
8. Warranty and Support
The LINGXIAO Pool Booster Pump comes with a 2-Year Manufacturer's Warranty. This warranty covers defects in materials and workmanship under normal use and service.
For warranty claims, technical assistance, or any questions regarding your product, please contact LINGXIAO customer support. Refer to the contact information provided on the product packaging or the official LINGXIAO website.
Online Resources:
- Visit the LINGXIAO Store on Amazon: LINGXIAO Store
